What rims/tires will fit a stock-like application? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Christians Fleetside · 12-31-2017, 10:49 PM

My son and I just started working on a 1958 Chevy Fleetside that had been sitting in the Arizona desert for 40 years. It has some ridiculous 10" wide rims in the rear and 7" inch in the front. We are on a tight budget and we want to make the truck close to stock. Just to get it rolling I want to put the 7" rims in the back and get a couple steel rims for the front that would be close to stock.
1) What is the stock rim size for a 1958 3200(six bolt)? The spare appears to be around 15" x 7"
2) Is there a match from a later model car or truck that would fit?
3) What was the stock tire size? The spare tire says 8.45-15 and has a diameter of about 28 inches
Thanks in advance
Paul

4544speed · 01-01-2018, 02:18 AM

Can't answer 1 & 3 but as far as other wheels that might fit. That same bolt pattern - 6 x 5.5" (6 x 139.7mm) - was used on the Toyota tundra from 2000 to 2006 so there are 15-16 inch wheels that will fit. Just get the proper lug nuts. I bought a set of 4 off CL with worn tires to use as a rollers for 40 bucks. The same pattern was used by Chevy for years. Make sure the center hole is large enough to fit your drums !!

OrrieG · 01-01-2018, 04:59 PM

70s C/K trucks ran both 15 and 16" wheels in 6 bolt pattern, 7" wide at the bead. Only negative is you cannot run stock 50's hub caps. It took a while but I found a set of 68-72 caps and beauty rings. Also, 67 passenger caps will fit some wheels. Here is photo of both.

Foot Stomper · 01-01-2018, 07:11 PM

You can look around for the stock 15" (or 16" but very rare) rims that have three hub cap clips. The 3 clip rims are 55.2 to 59 and have a 4.5" width. You might find some 6 clip rims, but they are 55.1 and older and are 4" wide.
Pictured is a 16" 3 clip. (not for sale)

**1project2many** · 01-01-2018, 08:52 PM

Wheels from a mid '70s to '80s K1500 fit and generally don't look too bad. I'm running 16" rims from a horse trailer on my truck.

59chev · 01-01-2018, 10:34 PM

I ran the 80's rims with beauty rings and chrome acorn nuts when my truck was stock and had the 6 bolt pattern. I liked the look, I pieced together a set from 3 different wrecking yards, then sandblasted and painted them.

bobinbc · 01-02-2018, 03:26 AM

For stock appearing wheels Chevy 2wd trucks up to about 66-67 I think and 4wd for many years after that but check center hole size as already mentioned.

Here's a link to tons of info about your truck including original wheel and tire sizes https://gmheritagecenter.com/docs/gm...olet-Truck.pdf

Welcome to the group!

Black_Sheep · 01-02-2018, 08:48 PM

https://www.wheelvintiques.com/wheel...re-finish.html

15 x 7 with 6 on 5.5 bolt pattern are $64, if you buy through Summit Racing I think they will ship free

nail pounder · 01-02-2018, 11:19 PM

I bought one of these to run as a spare. Looks pretty close to stock. You could probably put clips on them and run hubcaps if you wanted.
https://www.etrailer.com/dept-pg-Tir...c-15_Inch.aspx

12-31-2017, 10:49 PM	#1
Christians Fleetside Registered User Join Date: Dec 2017 Location: Yuma Posts: 1	What rims/tires will fit a stock-like application? My son and I just started working on a 1958 Chevy Fleetside that had been sitting in the Arizona desert for 40 years. It has some ridiculous 10" wide rims in the rear and 7" inch in the front. We are on a tight budget and we want to make the truck close to stock. Just to get it rolling I want to put the 7" rims in the back and get a couple steel rims for the front that would be close to stock. 1) What is the stock rim size for a 1958 3200(six bolt)? The spare appears to be around 15" x 7" 2) Is there a match from a later model car or truck that would fit? 3) What was the stock tire size? The spare tire says 8.45-15 and has a diameter of about 28 inches Thanks in advance Paul

01-01-2018, 02:18 AM	#2
4544speed Registered User Join Date: Jan 2013 Location: League City, TX Posts: 83	Re: What rims/tires will fit a stock-like application? Can't answer 1 & 3 but as far as other wheels that might fit. That same bolt pattern - 6 x 5.5" (6 x 139.7mm) - was used on the Toyota tundra from 2000 to 2006 so there are 15-16 inch wheels that will fit. Just get the proper lug nuts. I bought a set of 4 off CL with worn tires to use as a rollers for 40 bucks. The same pattern was used by Chevy for years. Make sure the center hole is large enough to fit your drums !!

01-01-2018, 04:59 PM	#3
OrrieG Registered User Join Date: Jun 2006 Location: Idaho Posts: 8,800	Re: What rims/tires will fit a stock-like application? 70s C/K trucks ran both 15 and 16" wheels in 6 bolt pattern, 7" wide at the bead. Only negative is you cannot run stock 50's hub caps. It took a while but I found a set of 68-72 caps and beauty rings. Also, 67 passenger caps will fit some wheels. Here is photo of both. Attached Images __________________ 1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread 1964 Chevelle Malibu w/ 355-350TH (daily driver) Helpful AD and TF Manual Site Old Car Manual Project

01-01-2018, 07:11 PM	#4
Foot Stomper Registered User Join Date: Oct 2015 Location: Calgary, Alberta Posts: 1,252	Re: What rims/tires will fit a stock-like application? You can look around for the stock 15" (or 16" but very rare) rims that have three hub cap clips. The 3 clip rims are 55.2 to 59 and have a 4.5" width. You might find some 6 clip rims, but they are 55.1 and older and are 4" wide. Pictured is a 16" 3 clip. (not for sale) Attached Images __________________ So when is this "Old enough to know better" supposed to kick in? My 1959 GMC build thread http://67-72chevytrucks.com/vboard/s...d.php?t=686989

01-01-2018, 08:52 PM	#5
1project2many Senior Member Join Date: Mar 2012 Location: Lakes Region NH Posts: 3,217	Re: What rims/tires will fit a stock-like application? Wheels from a mid '70s to '80s K1500 fit and generally don't look too bad. I'm running 16" rims from a horse trailer on my truck.

01-01-2018, 10:34 PM	#6
59chev Registered User Join Date: Apr 2007 Location: Calgary, Alberta Posts: 441	Re: What rims/tires will fit a stock-like application? I ran the 80's rims with beauty rings and chrome acorn nuts when my truck was stock and had the 6 bolt pattern. I liked the look, I pieced together a set from 3 different wrecking yards, then sandblasted and painted them. Attached Images __________________ My Build Thread: 59 Apache - Lifelong obsession http://67-72chevytrucks.com/vboard/showthread.php?t=622133"]59 Apache - Lifelong obsession

01-02-2018, 03:26 AM	#7
bobinbc Registered User Join Date: Mar 2009 Location: Vancouver Island, Courtenay B.C. CANADA Posts: 578	Re: What rims/tires will fit a stock-like application? For stock appearing wheels Chevy 2wd trucks up to about 66-67 I think and 4wd for many years after that but check center hole size as already mentioned. Here's a link to tons of info about your truck including original wheel and tire sizes https://gmheritagecenter.com/docs/gm...olet-Truck.pdf Welcome to the group! __________________ 1962 Chevy blue SBFS 1957 Chevy yellow SBSS 1956 GMC red SBSS Nov 2017 ToTM https://www.facebook.com/groups/Cana...geChevyTrucks/

01-02-2018, 08:48 PM	#8
Black_Sheep Registered User Join Date: Jun 2017 Location: upper midwest Posts: 1,129	Re: What rims/tires will fit a stock-like application? https://www.wheelvintiques.com/wheel...re-finish.html 15 x 7 with 6 on 5.5 bolt pattern are $64, if you buy through Summit Racing I think they will ship free __________________ Mark Brother's keeper - '58 Stepside build

01-02-2018, 11:19 PM	#9
nail pounder Registered User Join Date: Aug 2014 Location: Fallbrook CA Posts: 453	Re: What rims/tires will fit a stock-like application? I bought one of these to run as a spare. Looks pretty close to stock. You could probably put clips on them and run hubcaps if you wanted. https://www.etrailer.com/dept-pg-Tir...c-15_Inch.aspx Attached Images



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.