|
02-25-2018, 11:45 PM
|
#1 |
|
Registered User
Join Date: Jan 2015
Location: apple valley california
Posts: 98
|
Drive line questions
Just dropped a LQ4 in my 1960 suburban build is on this site. i have all angles correct for the drive line and was wondering what everyone is doing i would like to go as small O.D. as possible do to some upward clearance issues. Everything i am reading says i need to be at like 6" O.D. for 55" length what is everyone doing or am i just reading incorrectly?
|
|
|
|
02-26-2018, 12:18 AM
|
#2 |
|
Registered User
Join Date: Jan 2013
Location: Las Vegas, NV
Posts: 1,857
|
Re: Drive line questions
X- frame? I went two-piece because of X tunnel issues.
__________________
1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081 |
|
|
|
|
02-26-2018, 12:34 AM
|
#3 |
|
60-66 Nut
  Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,252
|
Re: Drive line questions
There is absolutely nothing wrong with a 2pc driveshaft as long as you use a good HD carrier bearing. I am not familiar with what is available for the '60-'62's but it looks like LVPhotos has a good strong driveshaft assembly.
__________________
Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE |
|
|
|
|
02-26-2018, 12:52 AM
|
#4 |
|
Registered User
Join Date: Jan 2015
Location: apple valley california
Posts: 98
|
Re: Drive line questions
thanks LVPHOTOS I read you stream good stuff really nice tuck. DO you have any better photos of where you mounted the carrier bearing? or did the drive line shop do it for you? Looks like that's the way I'm going.
|
|
|
|
|
02-26-2018, 12:56 PM
|
#5 |
|
Registered User
Join Date: Jan 2013
Location: Las Vegas, NV
Posts: 1,857
|
Re: Drive line questions
I started with the original 283/3 speed, went to the T-5 in 98? Original shaft shorted and T5 built Buy Adams Driveline. My 400 block was found in garbage can for $100-- lol. Now the new Eaton gear drive Tru-track and drive shaft built by them. They build Jeep stuff all day, bus, limo, low rider and odd stuff. Check FB page for hard evidence how we abuse shafts. We went over issues of the tunnel and even being short bed this was the verdict. I believe it was $600 These guys ship everywhere and are quick in turn around. They work on all my gear boxes.
http://adamsdriveshaftoffroad.com
__________________
1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081 |
|
|
|
|
02-26-2018, 01:22 PM
|
#6 |
|
Registered User
Join Date: Jan 2013
Location: Las Vegas, NV
Posts: 1,857
|
Re: Drive line questions
If you can Frakinstine a toy, they can shaft it.
__________________
1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081 |
|
|
|
|
02-26-2018, 06:36 PM
|
#7 |
|
Registered User
Join Date: Oct 2016
Location: san bernardino ca
Posts: 1,611
|
Re: Drive line questions
My drive shaft shop said no more then 60 in on a 1 piece.
|
|
|
|
|
02-27-2018, 09:11 AM
|
#8 |
|
Registered User
Join Date: Nov 2015
Location: Western Nebraska
Posts: 43
|
Re: Drive line questions
Yep. Two piece with a good carrier bearing is the way to go. Had a 2 piece shortened and balanced for my '63 long bed: has held up fine behind my 383.
__________________
Jake Old fart in Western NE |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
