'65 blower resistor location - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jmcap · 03-19-2018, 10:28 AM

Hi Guys,

Helping my son get his old truck up to snuff. Just ordered a new heater wiring harness and resistor. It's a Deluxe model. Bench tested the motor it's fine. Under the dash is a nightmare. Correct me if I'm wrong but I believe the resistor mounts to an opening in the air box. Here in lies my confusion. There appears to be a rectangular patch over what I assume was an opening located pretty far up the box on the passenger side. As well there is another opening just to the left of the passenger's floor vent. It's a larger rectangle. Anyone have a picture to share of the resistor mounted as well as the ducts for the driver's floor side and defroster ?

A second point of confusion is where the 'temperature cable' at the control is mounted. The control panel is minus the control levers at the present time so I'm in the guessing stage. The cables for the defroster and air are obvious because their labeled. The center lever is defined as fan........ obviously somehow controls the switch. Does it as well control the temperature cable?? Any ifo would be deeply appreciated.

**The Rocknrod** · 03-19-2018, 11:25 AM

Here is the answer - http://67-72chevytrucks.com/vboard/s...88&postcount=6
LMC has replacements.
Some more info with a manual pic - http://67-72chevytrucks.com/vboard/s...d.php?t=579293
And there is a long thread named "All About Heaters" here - http://67-72chevytrucks.com/vboard/s...d.php?t=488618

jmcap · 03-19-2018, 01:17 PM

RockinRod,

Thanks. So I think what you showed me is that the resistor is installed to the interior of the box at the interior side of the firewall. At 71 years old I'm not new to backyard mechanics. I'll happily take it apart to see what you showed me. Next guestion therefore is where do the wiring harness wires route?

**The Rocknrod** · 03-19-2018, 01:38 PM

I know yours is a 65 but it cant be much different - http://67-72chevytrucks.com/vboard/s...4&postcount=50

**The Rocknrod** · 03-19-2018, 01:43 PM

Even better.
On this thread is your info - http://67-72chevytrucks.com/vboard/s...d.php?t=672205
Specifically this post -
http://67-72chevytrucks.com/vboard/s...53&postcount=6

jmcap · 03-19-2018, 01:46 PM

Rocknrod,

Thank you so much. Will let you know how I do.

jmcap

03-19-2018, 10:28 AM	#1
jmcap Registered User Join Date: Mar 2018 Location: East Hanover, NJ Posts: 46	'65 blower resistor location Hi Guys, Helping my son get his old truck up to snuff. Just ordered a new heater wiring harness and resistor. It's a Deluxe model. Bench tested the motor it's fine. Under the dash is a nightmare. Correct me if I'm wrong but I believe the resistor mounts to an opening in the air box. Here in lies my confusion. There appears to be a rectangular patch over what I assume was an opening located pretty far up the box on the passenger side. As well there is another opening just to the left of the passenger's floor vent. It's a larger rectangle. Anyone have a picture to share of the resistor mounted as well as the ducts for the driver's floor side and defroster ? A second point of confusion is where the 'temperature cable' at the control is mounted. The control panel is minus the control levers at the present time so I'm in the guessing stage. The cables for the defroster and air are obvious because their labeled. The center lever is defined as fan........ obviously somehow controls the switch. Does it as well control the temperature cable?? Any ifo would be deeply appreciated.

03-19-2018, 11:25 AM	#2
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: '65 blower resistor location Here is the answer - http://67-72chevytrucks.com/vboard/s...88&postcount=6 LMC has replacements. Some more info with a manual pic - http://67-72chevytrucks.com/vboard/s...d.php?t=579293 And there is a long thread named "All About Heaters" here - http://67-72chevytrucks.com/vboard/s...d.php?t=488618 __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

03-19-2018, 01:17 PM	#3
jmcap Registered User Join Date: Mar 2018 Location: East Hanover, NJ Posts: 46	Re: '65 blower resistor location RockinRod, Thanks. So I think what you showed me is that the resistor is installed to the interior of the box at the interior side of the firewall. At 71 years old I'm not new to backyard mechanics. I'll happily take it apart to see what you showed me. Next guestion therefore is where do the wiring harness wires route?

03-19-2018, 01:38 PM	#4
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: '65 blower resistor location I know yours is a 65 but it cant be much different - http://67-72chevytrucks.com/vboard/s...4&postcount=50 __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

03-19-2018, 01:43 PM	#5
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: '65 blower resistor location Even better. On this thread is your info - http://67-72chevytrucks.com/vboard/s...d.php?t=672205 Specifically this post - http://67-72chevytrucks.com/vboard/s...53&postcount=6 __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

03-19-2018, 01:46 PM	#6
jmcap Registered User Join Date: Mar 2018 Location: East Hanover, NJ Posts: 46	Re: '65 blower resistor location Rocknrod, Thank you so much. Will let you know how I do. jmcap



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.