Need some help, hope you guys can help me out! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Chris04 · 05-30-2018, 03:45 PM

Hey guys, I’ve searched and can not seem to find what I’m looking for! I have a 67 pickup that I want to add the chrome hood trim across the front and on the sides beside headlight bezels. I’m not sure where to drill holes for the side pieces, I can figure out the hood piece being it has studs in it, just wondering if anyone has any measurements or any pics of theirs. Any help would be greatly appreciated!

Chris

demian5 · 05-30-2018, 04:07 PM

Having the trim and retainers should answer your questions. And searching for fender pictures should do it.

Chris04 · 05-30-2018, 09:00 PM

Ok so I got the side little ones mounted and they look great but the top hood trim is going to be a different animal. Does anyone have a pic of a hood with the factory holes so I can get a idea of where to drill holes! It’s so hard to hold the trim to the edge of hood with the studs sticking out and get an idea of where it’s suppose to be drilled. It almost looks like it’s suppose to be in the crease. Any help appreciated I could not find a pic with holes anywhere, just holes for letters! Thanks

Chris

Chris04 · 05-31-2018, 10:51 AM

I’m surprised no one on here has any pics.

Coley · 05-31-2018, 12:20 PM

Quote:

Originally Posted by Chris04

I’m surprised no one on here has any pics.

Be patient....no one is necessarily running out to their trucks to take immediate pics for your request.
As time allows, the guys should be able to help you out....so hang in there.

All good
Coley

Chris04 · 05-31-2018, 01:01 PM

I don’t expect anyone to run out and take pics just for me, I just figured there are plenty of ppl who have done the same thing I have and would have old pics or a guide someone gave them to go by. Didn’t mean to rush anyone, just needed some help. Thanks

OARNGESI · 05-31-2018, 01:47 PM

Just tape it in place and outline it with a pencil for a guide

Chris04 · 05-31-2018, 02:48 PM

Quote:

Originally Posted by OARNGESI

Just tape it in place and outline it with a pencil for a guide

Wish I could, prob is the studs stick out an inch and I can’t lay it flat to see where to drill holes, I tried removing studs and no way to, they are all on a long sleeve made inside of it, I ordered it from lmc and it doesn’t look like it will fit very well as it is, aftermarket stuff can be good and bad, just on the edge with drilling holes in my hood and messing up.

**LockDoc** · 05-31-2018, 02:59 PM

-
Don't know if you can get anything from this or not. From the assembly manual.

If you buy an assembly manual buy the CD version because you can search it for key words. I just typed in the word "Hood".

LockDoc

demian5 · 05-31-2018, 03:01 PM

Quote:

Originally Posted by LockDoc

-
Don't know if you can get anything from this or not. From the assembly manual.

If you buy an assembly manual buy the CD version because you can search it for key words. I just typed in the word "Hood".

LockDoc

Its not gonna get much better than that. It has actual dimensions.

zosoppp · 05-31-2018, 03:08 PM

Make some sort of paper template by poking the paper over the back of the trim piece studs. Mark the ends or other important alignment locations on the paper then put the template on the body part and you should have a location for the hole centers.

Chris04 · 05-31-2018, 06:02 PM

Quote:

Originally Posted by LockDoc

-
Don't know if you can get anything from this or not. From the assembly manual.

If you buy an assembly manual buy the CD version because you can search it for key words. I just typed in the word "Hood".

LockDoc

That’s perfect!! Thanks so much.

Chris

Chris04 · 05-31-2018, 06:02 PM

Quote:

Originally Posted by zosoppp

Make some sort of paper template by poking the paper over the back of the trim piece studs. Mark the ends or other important alignment locations on the paper then put the template on the body part and you should have a location for the hole centers.

Great idea! Thanks man

**CC69Rat** · 05-31-2018, 07:55 PM

http://67-72chevytrucks.com/vboard/s...=444414&page=3

Post # 68 might help to kinda see where the holes should be drilled. These are factory GM parts, original holes.

**Harleys 4 You** · 10-02-2018, 09:41 PM

ttt

05-30-2018, 03:45 PM	#1
Chris04 Registered User Join Date: Apr 2014 Location: Galivants ferry, South Carolina Posts: 189	Need some help, hope you guys can help me out! Hey guys, I’ve searched and can not seem to find what I’m looking for! I have a 67 pickup that I want to add the chrome hood trim across the front and on the sides beside headlight bezels. I’m not sure where to drill holes for the side pieces, I can figure out the hood piece being it has studs in it, just wondering if anyone has any measurements or any pics of theirs. Any help would be greatly appreciated! Chris __________________ 1972 Cheyenne super 1949 3100

05-30-2018, 04:07 PM	#2
demian5 Registered User Join Date: Aug 2016 Location: Lake Forest, CA Posts: 2,178	Re: Need some help, hope you guys can help me out! Having the trim and retainers should answer your questions. And searching for fender pictures should do it. __________________ "Work hard, use your vacation days." 1970 C15 GMC Long Bed 1986 C20 Scottsdale 1983 K2500 Sierra Classic Suburban 6.2 Instagram: C10sofOC

05-30-2018, 09:00 PM	#3
Chris04 Registered User Join Date: Apr 2014 Location: Galivants ferry, South Carolina Posts: 189	Re: Need some help, hope you guys can help me out! Ok so I got the side little ones mounted and they look great but the top hood trim is going to be a different animal. Does anyone have a pic of a hood with the factory holes so I can get a idea of where to drill holes! It’s so hard to hold the trim to the edge of hood with the studs sticking out and get an idea of where it’s suppose to be drilled. It almost looks like it’s suppose to be in the crease. Any help appreciated I could not find a pic with holes anywhere, just holes for letters! Thanks Chris __________________ 1972 Cheyenne super 1949 3100

05-31-2018, 10:51 AM	#4
Chris04 Registered User Join Date: Apr 2014 Location: Galivants ferry, South Carolina Posts: 189	Re: Need some help, hope you guys can help me out! I’m surprised no one on here has any pics. __________________ 1972 Cheyenne super 1949 3100

05-31-2018, 01:01 PM	#6
Chris04 Registered User Join Date: Apr 2014 Location: Galivants ferry, South Carolina Posts: 189	Re: Need some help, hope you guys can help me out! I don’t expect anyone to run out and take pics just for me, I just figured there are plenty of ppl who have done the same thing I have and would have old pics or a guide someone gave them to go by. Didn’t mean to rush anyone, just needed some help. Thanks __________________ 1972 Cheyenne super 1949 3100

05-31-2018, 01:47 PM	#7
OARNGESI Registered User Join Date: Sep 2008 Location: CASA GRANDE AZ Posts: 4,276	Re: Need some help, hope you guys can help me out! Just tape it in place and outline it with a pencil for a guide __________________ 70 SWB STEPSIDE 70 BLAZER 09 challenger

05-31-2018, 02:59 PM	#9
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,891	Re: Need some help, hope you guys can help me out! - Don't know if you can get anything from this or not. From the assembly manual. If you buy an assembly manual buy the CD version because you can search it for key words. I just typed in the word "Hood". LockDoc Attached Images __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

05-31-2018, 03:08 PM	#11
zosoppp Registered User Join Date: Mar 2014 Location: Lincoln Park, NJ Posts: 193	Re: Need some help, hope you guys can help me out! Make some sort of paper template by poking the paper over the back of the trim piece studs. Mark the ends or other important alignment locations on the paper then put the template on the body part and you should have a location for the hole centers. __________________ 1970 C10 LWB 350SBC, SM330 Muncie (not saginaw SM326) (on tree), 3.07 open (assumed), PS, PB, Idiot lights

05-31-2018, 07:55 PM	#14
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,216	Re: Need some help, hope you guys can help me out! http://67-72chevytrucks.com/vboard/s...=444414&page=3 Post # 68 might help to kinda see where the holes should be drilled. These are factory GM parts, original holes. __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

10-02-2018, 09:41 PM	#15
Harleys 4 You Senior Member Join Date: Jul 2011 Location: Wichita, KS Posts: 525	Re: Need some help, hope you guys can help me out! ttt



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.