|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-10-2018, 08:42 PM
|
#1 |
|
Registered User
Join Date: Jul 2002
Location: Chesnee SC
Posts: 254
|
Do I need a high hump for a 4L60E?
Hey folks. I haven’t been on here in a while with a question but finally getting back to my project. Was wondering do I need a high hump trans tunnel to run a 4L80E and a 5.3 or will a low hump work just fine? I was thinking the trans is bulkier on the driveshaft end of the trans. Thanks
__________________
1980 Malibu Classic 2 dr coupe 1964 Impala SS 4 speed 1968 GMC (major project) grandpa bought new 1969 Chevrolet C-10 Shortbed Fleetside 2008 GMC Canyon (daily driver) Last edited by Bryan H; 09-10-2018 at 09:13 PM. |
|
|
|
09-10-2018, 09:16 PM
|
#2 |
|
Registered User
Join Date: Jul 2016
Location: Gallatin TN
Posts: 376
|
Re: Do I need a high hump for a 4L60E?
I'm running a 6.2 with a 4L60E and the low hump works fine. It's tight on the top, just a couple of inches, but it fits OK. No issue with the column shifter hooking up either, I used a Lokar rod kit. Had to bend it a little, but it works excellent.
On a previous build, I had a 5.3 with a 4L60E there as well, no issues with either one. Hope this helps, and good luck!! |
|
|
|
|
09-10-2018, 09:21 PM
|
#3 |
|
Moderator
 
Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,204
|
Re: Do I need a high hump for a 4L60E?
Ditto on the no need for the high hump...
Have mine installed now and no worries with clearance... 
__________________
Family and country before all others... 2006 Chevy Silverado (Daily Driver) 2012 Chevy Equinox 
|
|
|
|
|
09-10-2018, 09:44 PM
|
#4 |
|
Registered User
Join Date: Jul 2002
Location: Chesnee SC
Posts: 254
|
Re: Do I need a high hump for a 4L60E?
Thanks y’all.
__________________
1980 Malibu Classic 2 dr coupe 1964 Impala SS 4 speed 1968 GMC (major project) grandpa bought new 1969 Chevrolet C-10 Shortbed Fleetside 2008 GMC Canyon (daily driver) |
|
|
|
|
09-11-2018, 10:58 AM
|
#5 |
|
Registered User
Join Date: Apr 2015
Location: New Sharon iowa
Posts: 75
|
Re: Do I need a high hump for a 4L60E?
low hump and 4l60e combo work with truck pan oil pan on a slammed truck? im about to fit the engine but heard I might need a f body oil pan.
__________________
1965 C10 long box laid out on bags instgram 65see_x .……………………….. ____ ..………________//__l \_____ ,,,,,,,/__(O)___//___/__(O)_/ |
|
|
|
|
09-11-2018, 11:01 AM
|
#6 |
|
1965 Chevy C10, 2005 4.8L/4l60
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,546
|
Re: Do I need a high hump for a 4L60E?
Anything lower than 4” in the front will need the fbody pan
__________________
Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684  support our troops! |
|
|
|
|
09-11-2018, 11:02 AM
|
#7 |
|
Registered User
Join Date: Apr 2015
Location: New Sharon iowa
Posts: 75
|
Re: Do I need a high hump for a 4L60E?
thanks I wasn't sure if I could raise the whole engine and tranny up or not.
__________________
1965 C10 long box laid out on bags instgram 65see_x .……………………….. ____ ..………________//__l \_____ ,,,,,,,/__(O)___//___/__(O)_/ |
|
|
|
|
09-11-2018, 04:59 PM
|
#8 | |
|
Senior Member
Join Date: Jun 2016
Location: Beebe, AR
Posts: 462
|
Re: Do I need a high hump for a 4L60E?
Quote:
CTS-V pan works pretty good. Bubba |
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
