The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-06-2018, 11:40 PM   #1
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
What’s the most practical way to swap engines?

Ok so I finally found a project truck. 56 GMC stepside. Body is really good considering the age. Floors are unbelievably solid. Cab corners are shot but fixable. Front fenders need some love or just replaced. Interior is wasted but that’s just cosmetic stuff that can wait. For me the first order of business would be a drivetrain and brakes.
I was thinking about a 350 w/700r4 trans. What’s the most practical way to go about it? Is there a certain year of engine/trans I should be looking for? Best mounts and/or crossmember to use? I do not want to change the front suspension. I will eventually put disk brakes on the front. Was thinking PS/PB as well eventually. Other than that i don’t plan on veering too far from stock.
Thanks in advance
Phungki is offline   Reply With Quote
Old 11-07-2018, 12:18 AM   #2
mikebte
Registered User
 
Join Date: Oct 2011
Location: Tucson, AZ
Posts: 639
Re: What’s the most practical way to swap engines?

What engine is currently in the GMC? Ether way your doing a big swap going to auto and power steering.
Are you on a budget? I like to think we all are, if your wanting to go cheap you could buy a doner vehicle and swap all the engine and trans stuff. That could be an LS car or and older TBI or carbed vehical. If wanting all new, I would get with a supplier like CPP and get all the conversion items needed. Power steering box and pump, disk brakes, crossmember. Look at some of the build threads and get some ideas.

What rear end is in the truck? The stock gears if 3.90 or 4.11 should be OK with an OD trans but if 3.38 it may be a little doggish.

Hope this helps. I used a 93 GMC parts truck and swapped the tbi engine and transmission stuff into my 59. Nothing was bolt in as much as I would have liked it to be.
mikebte is offline   Reply With Quote
Old 11-07-2018, 01:42 AM   #3
mick53
Registered User
 
Join Date: Oct 2018
Location: Warsaw IN
Posts: 897
Re: What’s the most practical way to swap engines?

I went with EPAS electric power steering, clean and simple.
mick53 is offline   Reply With Quote
Old 11-07-2018, 07:27 AM   #4
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
Re: What’s the most practical way to swap engines?

Quote:
Originally Posted by mikebte View Post
What engine is currently in the GMC? Ether way your doing a big swap going to auto and power steering.
Are you on a budget? I like to think we all are, if your wanting to go cheap you could buy a doner vehicle and swap all the engine and trans stuff. That could be an LS car or and older TBI or carbed vehical. If wanting all new, I would get with a supplier like CPP and get all the conversion items needed. Power steering box and pump, disk brakes, crossmember. Look at some of the build threads and get some ideas.

What rear end is in the truck? The stock gears if 3.90 or 4.11 should be OK with an OD trans but if 3.38 it may be a little doggish.

Hope this helps. I used a 93 GMC parts truck and swapped the tbi engine and transmission stuff into my 59. Nothing was bolt in as much as I would have liked it to be.
It currently has a 6 cylinder. Well...most of one 😄. I’m not sure what gears are in it. I’m on a budget but not a time line. I like the idea of a donor vehicle. What engine/tranny combo did you get out of your parts truck? I’ve noticed there are “bolt on” motor mounts for a 350 in these trucks. Don’t know how straight forward those are.
Thank you
Phungki is offline   Reply With Quote
Old 11-07-2018, 07:48 AM   #5
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
Re: What’s the most practical way to swap engines?

Quote:
Originally Posted by mick53 View Post
I went with EPAS electric power steering, clean and simple.
I will definitely look into this. I wondered if it was possible to utilize the power steering pump that came in whatever engine I put in it or if that would just be opening up a huge and possibly unnecessary project. I’m pretty much a newb when it comes to this. I’m sure I have bit off more than I can chew but I’m in no hurry.
Thank you for this idea
Phungki is offline   Reply With Quote
Old 11-07-2018, 11:23 AM   #6
yossarian19
Registered User
 
Join Date: Sep 2011
Location: Nevada City, CA
Posts: 908
Re: What’s the most practical way to swap engines?

I started with similar notions about keeping it stock-ish in the front suspension.
My experience is that by the time you add disc brakes, power steering, new bushings, new steering joints, etc you have spent darn near what an IFS might have cost you.
I've got new shackles, rear spring bushings, new king pins, new tie rod, C10 power steering (avoid like plague), disc brakes, tapered roller bearings, 4* caster wedges and probably some other junk into my I-beam front end.

It handles and steers like a boat, parks like a garbage truck and buzzes like a summ***** going down the freeway. With a Chevy 350 & 7004R you will have the power and gearing to go a lot faster than your front end will really keep up with. It still needs a ton of work to be "right" - partially because the C10 steering kit is such an engineering junk-show to begin with, partly because you are still gilding and spending money on 1957's worn-out parts that were designed well before interstate travel was hitting 80 mph.
Possible caveat there is that if you have really tight kingpin and spindle bores or go with a new drop axle, your junk will probably not buzz like mine does.
__________________
"Over my head"
1957 Chevy 3200, big rear window & 6 lug.
Front disc, power steering, Vortec 4.8 / 4L60E swap, hydro boost brakes & patina.
yossarian19 is offline   Reply With Quote
Old 11-07-2018, 12:38 PM   #7
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: What’s the most practical way to swap engines?

do you mean cheapest or literally the most practical? I dont want to assume one or the other but a lot of people use "practical" when they mean "cheapest"

the most practical way would be to buy a complete donor like mikebte suggests and take out every single part you need to swap over. I have a theory that a wiring harness/drivetrain doesnt inherently KNOW what chassis it is installed in, it just looks for certain inputs, and if you can make sure it has those inputs you will have a working system even with it laying on the ground. in aerospace they call it an "iron bird".

then look at what you cant reuse but need to. for example your donor may be a column shift auto but you cant add that to your stock column. your donor may be EFI but needs the harness pared down and a different gas tank with the same pump. lines may not switch over.

the easy part is mounting, buy or more likely build the mounts.
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 11-07-2018, 01:03 PM   #8
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
Re: What’s the most practical way to swap engines?

Quote:
Originally Posted by yossarian19 View Post
I started with similar notions about keeping it stock-ish in the front suspension.
My experience is that by the time you add disc brakes, power steering, new bushings, new steering joints, etc you have spent darn near what an IFS might have cost you.
I've got new shackles, rear spring bushings, new king pins, new tie rod, C10 power steering (avoid like plague), disc brakes, tapered roller bearings, 4* caster wedges and probably some other junk into my I-beam front end.

It handles and steers like a boat, parks like a garbage truck and buzzes like a summ***** going down the freeway. With a Chevy 350 & 7004R you will have the power and gearing to go a lot faster than your front end will really keep up with. It still needs a ton of work to be "right" - partially because the C10 steering kit is such an engineering junk-show to begin with, partly because you are still gilding and spending money on 1957's worn-out parts that were designed well before interstate travel was hitting 80 mph.
Possible caveat there is that if you have really tight kingpin and spindle bores or go with a new drop axle, your junk will probably not buzz like mine does.
I’m sure you are right on IFS handling infinitely better then these old things. Maybe one day I’ll go that route but initially I’ll keep the front axel as is. It won’t ever be a daily driver. I will drive it in town, 10 miles to the next town or 25 miles to my parents. Nothing over 55 mph.
Thank you
Phungki is offline   Reply With Quote
Old 11-07-2018, 01:14 PM   #9
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
Re: What’s the most practical way to swap engines?

Quote:
Originally Posted by joedoh View Post
do you mean cheapest or literally the most practical? I dont want to assume one or the other but a lot of people use "practical" when they mean "cheapest"

the most practical way would be to buy a complete donor like mikebte suggests and take out every single part you need to swap over. I have a theory that a wiring harness/drivetrain doesnt inherently KNOW what chassis it is installed in, it just looks for certain inputs, and if you can make sure it has those inputs you will have a working system even with it laying on the ground. in aerospace they call it an "iron bird".

then look at what you cant reuse but need to. for example your donor may be a column shift auto but you cant add that to your stock column. your donor may be EFI but needs the harness pared down and a different gas tank with the same pump. lines may not switch over.

the easy part is mounting, buy or more likely build the mounts.
I looked this morning on cl and found many possible donor vehicles with the engine/trans combo I think I want. Even auto with shifter on the floor which I want. What I’m wondering is about the wiring. They sell new harnesses for these truck. The newer the donor truck the more dependent on computer crap. Is there a range of year I should be looking for in a donor? What I want is minimal issues with a new harness and a donor drivetrain. I know I’ll have some.
By practical I mean what makes the most sense. What’s going to be the easiest. I’m in no hurry to have my finished project. This is just something to put my head into and take it off of the normal issues with life. I guess I would call it a hobby.
Thank you
Jason
Phungki is offline   Reply With Quote
Old 11-07-2018, 01:36 PM   #10
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: What’s the most practical way to swap engines?

its pretty simple these days to use a modernish (98-2010) donor and just buy a stand alone harness, you will need someone to flash the pcm for standalone but literally 8 wires to hook up. getting the right fuel system is the next hurdle, usuing the donor pump is the best way if you can pull it off. then cooling system, then gauges.
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 11-07-2018, 02:53 PM   #11
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
Re: What’s the most practical way to swap engines?

for x-members the most practical way i have found is to fabricate your own
most inexpensive x-members are universal fit and need to be cut, fit and welded
why cut, fit and weld someone else's metal?

power steering is a slippery slope. you'll need a new column as the old column is integrated into the steering box
if you decide to go ifs all your work/money comes out into the junk pile
yossarian has some good info in his post, reread his reply ten times
__________________
cool, an ogre smiley Ogre's 58 Truk build

how to put your truck year and build thread into your signature
shop air compressor timer
_Ogre is offline   Reply With Quote
Old 11-07-2018, 03:30 PM   #12
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
Quote:
Originally Posted by _Ogre View Post
for x-members the most practical way i have found is to fabricate your own
most inexpensive x-members are universal fit and need to be cut, fit and welded
why cut, fit and weld someone else's metal?

power steering is a slippery slope. you'll need a new column as the old column is integrated into the steering box
if you decide to go ifs all your work/money comes out into the junk pile
yossarian has some good info in his post, reread his reply ten times
Ok so if I went IFS, what are my best options?
Posted via Mobile Device
Phungki is offline   Reply With Quote
Old 11-07-2018, 04:40 PM   #13
mikebte
Registered User
 
Join Date: Oct 2011
Location: Tucson, AZ
Posts: 639
Re: What’s the most practical way to swap engines?

Quote:
Originally Posted by Phungki View Post
I looked this morning on cl and found many possible donor vehicles with the engine/trans combo I think I want. Even auto with shifter on the floor which I want. What I’m wondering is about the wiring. They sell new harnesses for these truck. The newer the donor truck the more dependent on computer crap. Is there a range of year I should be looking for in a donor? What I want is minimal issues with a new harness and a donor drivetrain. I know I’ll have some.
By practical I mean what makes the most sense. What’s going to be the easiest. I’m in no hurry to have my finished project. This is just something to put my head into and take it off of the normal issues with life. I guess I would call it a hobby.
Thank you
Jason
honestly, look for a V8 truck or car, shifter location can be moved no matter the platform. Get a used car or truck and move over everything you want. In my case with the 93 GMC I used the entire cab harness from the 93. I now have courtesy lights, newer wiring, fuel injection and the fuel pump wiring was already in the harness and it was very simple. It will be a little time consuming if you are using the old harness as you have to figure out the locations for wires when doing a custom gauge install.

As for newer engines, the electronics are not bad. Many of them will last a long time and you get the ease of fuel injected start ups and an electronic shift transmission.

If you get a truck as a doner, the cross member may only need shortened and bolted in, the engine mount will be the biggest custom part you have and that is very easy.

You can also use this kit, easy enough.
https://www.summitracing.com/parts/c...etxk/overview/

Also check out other builds. I have taken so many ideas from the folks on here that its crazy. I found that OrrieG used a foot brake pedal out of a 70-80s blazer in his truck. So i adapted the same idea and it was super easy.

Mainly, its your build. Have fun and keep it unique.
mikebte is offline   Reply With Quote
Old 11-07-2018, 06:45 PM   #14
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
Re: What’s the most practical way to swap engines?

Quote:
Originally Posted by mikebte View Post
honestly, look for a V8 truck or car, shifter location can be moved no matter the platform. Get a used car or truck and move over everything you want. In my case with the 93 GMC I used the entire cab harness from the 93. I now have courtesy lights, newer wiring, fuel injection and the fuel pump wiring was already in the harness and it was very simple. It will be a little time consuming if you are using the old harness as you have to figure out the locations for wires when doing a custom gauge install.

As for newer engines, the electronics are not bad. Many of them will last a long time and you get the ease of fuel injected start ups and an electronic shift transmission.

If you get a truck as a doner, the cross member may only need shortened and bolted in, the engine mount will be the biggest custom part you have and that is very easy.

You can also use this kit, easy enough.
https://www.summitracing.com/parts/c...etxk/overview/

Also check out other builds. I have taken so many ideas from the folks on here that its crazy. I found that OrrieG used a foot brake pedal out of a 70-80s blazer in his truck. So i adapted the same idea and it was super easy.

Mainly, its your build. Have fun and keep it unique.
Thank you
I have been poking around this forum for awhile trying to decide the best course of action. Trying to decide which way I want to go. I’m still not sure. I know EFI is nice, not sold on it. Kinda like the old school carb. Is figuring out the wiring going to be more difficult using a newer donor compared to an older one? I’ve never done auto wiring. I rewired my whole house tho 😁. Yes I know that it’s completely different lol. I was hoping I could just buy a new harness and plug everything in, ripping out the old as I go. Nothing is that easy. If I was keeping the original motor that would be more if a possibility I’m guessing
Phungki is offline   Reply With Quote
Old 11-07-2018, 09:50 PM   #15
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: What’s the most practical way to swap engines?

I like using all the EFI and harness too, but it can get kind of crowded under hood.

IMG_2168 by Joe Doh, on Flickr
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 11-08-2018, 02:14 AM   #16
Jesse Z
Account Suspended
 
Join Date: Aug 2016
Location: Florida, USA
Posts: 290
Re: What’s the most practical way to swap engines?

Quote:
Originally Posted by yossarian19 View Post
I started with similar notions about keeping it stock-ish in the front suspension.

It handles and steers like a boat, parks like a garbage truck and buzzes like a summ***** going down the freeway. With a Chevy 350 & 7004R you will have the power and gearing to go a lot faster than your front end will really keep up with. It still needs a ton of work to be "right" - partly because you are still gilding and spending money on 1957's worn-out parts that were designed well before interstate travel was hitting 80 mph.
Shocking. I've had three I-beam axle trucks and all rode and handled great, both on winding rural roads and at freeway speeds. I can't imagine why you've had those problems but that certainly hasn't been my experience at all.
Jesse Z is offline   Reply With Quote
Old 11-08-2018, 07:42 AM   #17
1project2many
Registered User
 
Join Date: Mar 2012
Location: Lakes Region NH
Posts: 3,200
Re: What’s the most practical way to swap engines?

Quote:
I know EFI is nice, not sold on it. Kinda like the old school carb.
Both have advantages. My '57 has had EFI since the early '90s. It was more complicated to set up but I have had to do very little maintenance to the engine to keep it running since that time. My '36 Plymouth is still stock retaining points and a carb. It is very easy to service. Good thing because every year I have to clean and adjust the points, clean the sediment bowl, and clean the carb before the summer driving season begins.

Quote:
Is figuring out the wiring going to be more difficult using a newer donor compared to an older one?
Possibly. There are many more circuits in the newer vehicles and if you use a harness from a donor vehicle you will need to make decisions about which ones to keep and which ones to junk. But the popularity of the LS swap means there are many sources of help if you decide to use an LS engine.

Quote:
I was hoping I could just buy a new harness and plug everything in, ripping out the old as I go.
You can buy pre-made harnesses for nearly any engine /computer combination you might want to run. Many folks find that easier than ripping apart an OEM vehicle harness. Although quality plays a big role in harness pricing, it's also true that the cost of the harness will be proportional to the amount of work you are willing to invest on your end. A harness tailored to your truck, with length and circuits you specify, to connect to the engine and computer (and possibly transmission) you installed, will require a hand-built harness at greater cost. A generic harness which you adapt to your vehicle is likely to be less expensive.

Quote:
If I was keeping the original motor that would be more if a possibility I’m guessing
I would say it might be tougher. The original motor was never designed for computerized engine controls so you would be integrating sensors, injectors, and an electronic distributor which would add time and complication to your project. Retrofitting an old engine to modern electronics such as distributorless ignition and port fuel injection could be considered an advanced level project compared to removing the old engine and dropping in a complete donor vehicle engine.

Hmmm... considering IFS because it's better? LMK when you start the IFS swap in your Jeep.

Last edited by 1project2many; 11-08-2018 at 07:50 AM.
1project2many is offline   Reply With Quote
Old 11-08-2018, 09:33 AM   #18
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
Re: What’s the most practical way to swap engines?

Quote:
Originally Posted by 1project2many View Post
Both have advantages. My '57 has had EFI since the early '90s. It was more complicated to set up but I have had to do very little maintenance to the engine to keep it running since that time. My '36 Plymouth is still stock retaining points and a carb. It is very easy to service. Good thing because every year I have to clean and adjust the points, clean the sediment bowl, and clean the carb before the summer driving season begins.


Possibly. There are many more circuits in the newer vehicles and if you use a harness from a donor vehicle you will need to make decisions about which ones to keep and which ones to junk. But the popularity of the LS swap means there are many sources of help if you decide to use an LS engine.


You can buy pre-made harnesses for nearly any engine /computer combination you might want to run. Many folks find that easier than ripping apart an OEM vehicle harness. Although quality plays a big role in harness pricing, it's also true that the cost of the harness will be proportional to the amount of work you are willing to invest on your end. A harness tailored to your truck, with length and circuits you specify, to connect to the engine and computer (and possibly transmission) you installed, will require a hand-built harness at greater cost. A generic harness which you adapt to your vehicle is likely to be less expensive.


I would say it might be tougher. The original motor was never designed for computerized engine controls so you would be integrating sensors, injectors, and an electronic distributor which would add time and complication to your project. Retrofitting an old engine to modern electronics such as distributorless ignition and port fuel injection could be considered an advanced level project compared to removing the old engine and dropping in a complete donor vehicle engine.

Hmmm... considering IFS because it's better? LMK when you start the IFS swap in your Jeep.
lol wont be doing anything more to my Jeep. Love it just how it is. I imagine the 56 will get about the same amount of use as it does. No highway(well twice in the 3 yrs ive owned it, that includes driving it home lol). maybe 5k miles a year driven
I love the look and nostalgia of these old trucks which is why i dont want to have to veer real far from stock. i know I will have to in some degree and might decide to as the years go on but for now ill change only what is necessary. will it ride rough? probably more so than my grand cherokee but thats what i want. If i could have found a survivor that had drivetrain in it than that would have been awesome. Instead i looked for the best cab and frame i could find and went with that. Got pretty lucky in that department. a couple cab corners to weld in and thats it.
thank you for your response
Phungki is offline   Reply With Quote
Old 11-08-2018, 09:44 AM   #19
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
Re: What’s the most practical way to swap engines?

tell me if this is way off base pls. find a donor from 87 to 92 that has the 350/700r4 that im looking for and use as much of the donors wiring harness that i can. I can find a crossmember that conforms to this frame and matches up to the 700r4. Ive found engine mounts that do the same as well. Im new to this extensive automotive work so ple tell me if im heading into a complete nightmare that isnt likely to work.
My Dad has rebuilt a few cars in his day and has every tool one could want except a lift. He will be a big help i have no doubt but he is also a mopar/jeep guy(as i have always been, but this series of truck is too sexy to pass up lol). I already got the raised eyebrow when i told him about it.

any and all comments and info is appreciated. Im just trying to learn and not make too many costly mistakes. This is going to be my pasttime for the next few years so in getting it road worthy anyway.

thank you again to everyone who has commented on this thread
Phungki is offline   Reply With Quote
Old 11-08-2018, 10:18 AM   #20
mikebte
Registered User
 
Join Date: Oct 2011
Location: Tucson, AZ
Posts: 639
Re: What’s the most practical way to swap engines?

Quote:
Originally Posted by Phungki View Post
tell me if this is way off base pls. find a donor from 87 to 92 that has the 350/700r4 that im looking for and use as much of the donors wiring harness that i can. I can find a crossmember that conforms to this frame and matches up to the 700r4. Ive found engine mounts that do the same as well. Im new to this extensive automotive work so ple tell me if im heading into a complete nightmare that isnt likely to work.
My Dad has rebuilt a few cars in his day and has every tool one could want except a lift. He will be a big help i have no doubt but he is also a mopar/jeep guy(as i have always been, but this series of truck is too sexy to pass up lol). I already got the raised eyebrow when i told him about it.

any and all comments and info is appreciated. Im just trying to learn and not make too many costly mistakes. This is going to be my pasttime for the next few years so in getting it road worthy anyway.

thank you again to everyone who has commented on this thread
Sounds completely logical. 87-92 you have a good choice on 350 (TPI/ TBI/ Carb) and the 700R4 is not a computer controlled transmission, so if you opt to run the carb it will work just fine.

If you run into any issues on wiring, you know were to find all of us.
mikebte is offline   Reply With Quote
Old 11-09-2018, 03:29 AM   #21
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,710
Re: What’s the most practical way to swap engines?

I've always been a fan of buying a running driving donor for a project as long as it has the correct engine and trans you want for your project. That might be reasonably easy where you live as you can hunt down the good running V8 "winter rig" They may not be as cheap now as they would be in the spring though. That good running mid 80's two wheel drive pickup or maybe ex cop car caprice that runs great but is all rusted out might be a good cheap donor that you can sort out the engine and trans before you pull them.
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 11-09-2018, 09:51 AM   #22
Phungki
Registered User
 
Phungki's Avatar
 
Join Date: Sep 2018
Location: Blissfield MI
Posts: 252
Quote:
Originally Posted by mr48chev View Post
I've always been a fan of buying a running driving donor for a project as long as it has the correct engine and trans you want for your project. That might be reasonably easy where you live as you can hunt down the good running V8 "winter rig" They may not be as cheap now as they would be in the spring though. That good running mid 80's two wheel drive pickup or maybe ex cop car caprice that runs great but is all rusted out might be a good cheap donor that you can sort out the engine and trans before you pull them.
Yeah I think that’s what I’m going to do. They are all over cl right now and I’m sure they will be in the spring as well. I won’t be doing much this winter other than acquiring things that I need for it.
Thank yoy
Posted via Mobile Device
Phungki is offline   Reply With Quote
Old 12-05-2018, 01:12 PM   #23
washington blue
Registered User
 
Join Date: Mar 2016
Location: Not far from Sioux Falls South Dakota
Posts: 398
Re: What’s the most practical way to swap engines?

You say you are going to do a lot of around town driving and no high speed driving and nothing over 55mph. Don't mess with a 700r4, just put in a turbo hydro 350 tested tried and true. The 700r4 is for computer engines that run slow, about 1500rpm. A carburetor engine needs to run above 2000 rpm to work well. Most people don't know this because carburetors were phased out in 88. A Q jet 350 and a turbo 350 are the perfect combination for occasional use and slow speeds around town. No wiring headaches, you can fix anything on it, and it is going to sit most of the time so why make thing complicated?
washington blue is offline   Reply With Quote
Old 12-05-2018, 04:15 PM   #24
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 8,333
Re: What’s the most practical way to swap engines?

yep, if you want easy and quick buy a GOOD runner, not something that "just needs a tune up" or do the tune up while it is in the runner still. then take it all apart and slip it into your truck. these trucks came with a small block so you should be able to find mounts easy enough. the issue may come with the ifs swap because the original engine mounts are front mounts. you will also need to fit up a trans cross member but keep in mind that the original tranny cross also supports the cab and front spring rear mount areas for stiffness. you may wanna look at keeping some support there.
check out a few threads here, lots of those style of swaps.
dsraven is offline   Reply With Quote
Old 12-05-2018, 06:39 PM   #25
Missyblue
Registered User
 
Join Date: Jul 2017
Location: Fruita, co
Posts: 243
Re: What’s the most practical way to swap engines?

Hey I'm in your shoes and learning and this is what I'm told so far and trying for myself. my mechanic calls it my practical poor man plan

1988 to 1991chevy or gmc 2wd truck is what to look for if you want less wiring and flashing computer stuff. Once you get to 1992 you have the electronic tranny. has the tbi engine for fuel injection and the 700r4 then you supposedly can use lots of other stuff like suggested above out of the donor vehicle. but I liked his idea cause I can buy the truck and drive it and make sure everything works before putting in my truck. since you won't be drivin it a ton you buy one with around 100k and supposedly you will have an engine for the rest of your life haha. plus I'm not a person who can keep my carb tuned up and the fuel nowadays seems to make it harder he claimed.

there's a guy on Facebook Seth doulton in a Chevy/gmc forum I think that does really reasonable priced custom wiring kits I hear good things about. but there's tons of wiring companies just have to decide how much youb want to spend he's like $250 I think so much cheaper than alot i found.

it's an adventure. I originally planned to do like you and just upgrade my stock frobt with disk brakes and such but have since decided on a mustang ii after listening to these helpful gu ys on here. the cost and the benefits of what you gain are worth it to me since I'll be driving in town and need good handling and brakes and the cost of adding disk and powersteering was getting close so I'm saving for the better handling bonus as well haha

good luck and welcome. this forum is amazing and I have learned a little and have much to go. enjoy your build
Missyblue is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:45 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com