The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Tools, Shops and Shop Safety

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-14-2019, 10:21 AM   #1
pimpston65
Registered User
 
pimpston65's Avatar
 
Join Date: Aug 2013
Location: corktown,mi.
Posts: 5,194
gas welding vs mig

has anyone used gas welding with this welding for 18g panels as well as mig welding. i have very long sections to weld, and most have no access to the backside. so my issue is distortion control. so the question is, does gas welding do a better job for my application? thanks for replies...
Attached Images
 
pimpston65 is offline   Reply With Quote
Old 02-14-2019, 10:30 AM   #2
The Rocknrod
Moderator

 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
Re: gas welding vs mig

I would use a MIG 1/8" at a time and a wet rag on it fast after the stitch. Then move to a different area & repeat. May take longer but less distortion.
The Rocknrod is offline   Reply With Quote
Old 02-14-2019, 11:03 AM   #3
vin63
It's Better With Nitro
 
vin63's Avatar
 
Join Date: Apr 2008
Location: Chino Hills, CA
Posts: 2,262
Re: gas welding vs mig

Depending on the panel and location, I either TIG weld it with silicon bronze wire, or MIG weld it with .035, or thinner wire.
__________________
1963 C-10: Deluxe-optioned cab, shortbed, fleetside
Pontiac 462 ci, Kauffman D-Port alum. heads
4L80E, narrowed sheetmetal Ford 9-inch
Tubular front and rear suspension
Custom 6-piston front disc and 4-piston rear disc brakes
vin63 is offline   Reply With Quote
Old 02-14-2019, 11:30 AM   #4
LT1 Burb
Registered User
 
LT1 Burb's Avatar
 
Join Date: Sep 2010
Location: Winchester Oregon, formerly Vancouver BC
Posts: 2,949
Re: gas welding vs mig

I mig with .023 wire and never run a bead, spot only.
Attached Images
   
LT1 Burb is offline   Reply With Quote
Old 02-14-2019, 11:32 AM   #5
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 2,267
Re: gas welding vs mig

I have one of those torches at work, and I've played with it a bit. It claims to cut like plasma and weld like TIG. I was not impressed; I didn't find it any different.

Gas welding body panels together might be a better way to go than MIG, because the weld is annealed in the process, which should make hammering the weld out easier.

But you also run the risk of putting too much heat into the panel and having to deal with that.

Search up gas welding bodywork videos on Youtube and see if it's your cup of tea.

I'm not very good at it, honestly. I usually MIG.
__________________
1961 Apache: "Grabber Orange" Shortboxed, pancake, step-notch, air-ride, turbo, LS
1977 Silverado: Shortboxed & dropped, potato-potato
V8 Pontiac Firefly (Chevy Sprint): The ultimate engine swap: 5.7L in a 1.0L bag
Lotus Super 7 Replica: Scratch-built street-legal rollerskate
SkinnyG is offline   Reply With Quote
Old 02-14-2019, 02:08 PM   #6
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,670
Re: gas welding vs mig

I used my mig with .023 wire...using the spot method I had no real issues....
MP&C has a slick little gas welder setup...
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 02-14-2019, 03:12 PM   #7
MP&C
Registered User
 
MP&C's Avatar
 
Join Date: Jan 2013
Location: Leonardtown, MD
Posts: 1,648
Re: gas welding vs mig

Quote:
Originally Posted by pimpston65 View Post
has anyone used gas welding with this welding for 18g panels as well as mig welding. i have very long sections to weld, and most have no access to the backside. so my issue is distortion control. so the question is, does gas welding do a better job for my application? thanks for replies...

If you can do a no-filler fusion weld, the OA or Tig does a nice job, but I think gravity helps any welding on a horizontal plane to sag a bit, looking like an undercut. Once planished, it will tend to fill in any voids that you should see a fairly flat panel, both front and back, requiring little to no filing/grinding. The caveat here is that you absolutely need access to the rear side to be able to planish.


What areas are you welding that do not have rear access?
__________________
Robert
MP&C is offline   Reply With Quote
Old 02-14-2019, 05:43 PM   #8
pimpston65
Registered User
 
pimpston65's Avatar
 
Join Date: Aug 2013
Location: corktown,mi.
Posts: 5,194
Re: gas welding vs mig

Quote:
Originally Posted by MP&C View Post
If you can do a no-filler fusion weld, the OA or Tig does a nice job, but I think gravity helps any welding on a horizontal plane to sag a bit, looking like an undercut. Once planished, it will tend to fill in any voids that you should see a fairly flat panel, both front and back, requiring little to no filing/grinding. The caveat here is that you absolutely need access to the rear side to be able to planish.


What areas are you welding that do not have rear access?
the rear quarter on my suburban, both sides
pimpston65 is offline   Reply With Quote
Old 02-14-2019, 05:45 PM   #9
pimpston65
Registered User
 
pimpston65's Avatar
 
Join Date: Aug 2013
Location: corktown,mi.
Posts: 5,194
Re: gas welding vs mig

Quote:
Originally Posted by pimpston65 View Post
the rear quarter on my suburban, both sides
i have my mig setup for great welding, i just wanted to try another type of welding. thank you all for the input!!!
pimpston65 is offline   Reply With Quote
Old 02-14-2019, 06:45 PM   #10
MP&C
Registered User
 
MP&C's Avatar
 
Join Date: Jan 2013
Location: Leonardtown, MD
Posts: 1,648
Re: gas welding vs mig

You’re likely going to need planishing no matter the weld method, to remove the distortion. We’ve used long armed, double jointed, limber guys on the inside with a dolly and another on the outside with the hammer. Some light taps will find the dolly, then a couple good raps to stretch that weld back out, move on to the next.
__________________
Robert
MP&C is offline   Reply With Quote
Old 02-14-2019, 07:10 PM   #11
Stormin08
Registered User
 
Stormin08's Avatar
 
Join Date: Sep 2018
Location: Moss Bluff, LA
Posts: 381
Re: gas welding vs mig

i agree with the above mention of TIG. reason being, the filler is generally softer. what this leads to is...on a hot day, the filler will move with the panels.

i can always see a panel seam when done with GMAW or Oxy Fuel.

rarely does any DIY'er hammer finish the weld joint.
Stormin08 is offline   Reply With Quote
Old 02-16-2019, 07:47 PM   #12
sweetk30
Registered User
 
sweetk30's Avatar
 
Join Date: May 2012
Location: horseheads,ny rust belt
Posts: 2,794
Re: gas welding vs mig

have you looked in to the newer 2 part glue stuff made just for panel bonding ?

no heat / strong as a weld and the factory is using it all over the place these days .
__________________
77-k30lb BIG truck build .
87-k30lb budget beater build .
85-k30lb the plow machine build .
85-c10sb summer fun toy .
-----------------------------
HOLLEY SNIPER efi = worst case of p.i.t.a i ever had .

EDELBROCK pro flo 4 = best deal going so far . love my setup works great.
sweetk30 is offline   Reply With Quote
Old 02-16-2019, 11:44 PM   #13
pimpston65
Registered User
 
pimpston65's Avatar
 
Join Date: Aug 2013
Location: corktown,mi.
Posts: 5,194
Re: gas welding vs mig

Quote:
Originally Posted by sweetk30 View Post
have you looked in to the newer 2 part glue stuff made just for panel bonding ?

no heat / strong as a weld and the factory is using it all over the place these days .
i saw something about it, but never thought to use it.
pimpston65 is offline   Reply With Quote
Old 02-17-2019, 12:38 AM   #14
MP&C
Registered User
 
MP&C's Avatar
 
Join Date: Jan 2013
Location: Leonardtown, MD
Posts: 1,648
Re: gas welding vs mig

Quote:
Originally Posted by sweetk30 View Post
have you looked in to the newer 2 part glue stuff made just for panel bonding ?

no heat / strong as a weld and the factory is using it all over the place these days .
While it is true the factories are using glues, they don't use it in putting a seam down through the middle of a visible panel, as it more than likely will result in ghost lines in your paint. The glues require a flanged seam for the two panels to overlap, two thicknesses heat up and then cool down slower than one thickness. Given enough cycles of heating and cooling, the differing expansion and contraction rates will produce a ghost line showing exactly where the seam took place, like in this tailgate repair:


https://www.youtube.com/watch?v=OGhFEfVqxb0


Pimpston, one option may be to remove the entire quarter, make the needed repairs, and then replace. Or perhaps remove the outer wheelwell to provide access for planishing the weld seam and replace the wheelwell when complete. Or use the glue and live with ghost lines. This is exactly why weld seam locations should consider the need to planish the welds. Don't always take the smaller patch is better way of thinking, plan out the entire operation. Buy the larger panel if available if it makes the install easier, which may mean access for planishing. Use two people to planish if the inside and outside are not accessible by one.
__________________
Robert
MP&C is offline   Reply With Quote
Old 05-09-2019, 09:18 PM   #15
jeffahart
Senior Member
 
jeffahart's Avatar
 
Join Date: May 2012
Location: Scottsdale, AZ
Posts: 1,907
Re: gas welding vs mig

Quote:
Originally Posted by MP&C View Post
While it is true the factories are using glues, they don't use it in putting a seam down through the middle of a visible panel, as it more than likely will result in ghost lines in your paint. The glues require a flanged seam for the two panels to overlap, two thicknesses heat up and then cool down slower than one thickness. Given enough cycles of heating and cooling, the differing expansion and contraction rates will produce a ghost line showing exactly where the seam took place, like in this tailgate repair:
They are using it all over now like said above. They prefer a rivet bond over plug welding now too. Rivets over the structural adhesive joint. A cold repair/hybrid joint is a great way to repair if it's hidden, and your not going for an OEM restore. Not many places on our trucks for that though. I think it's mostly a modern assembly and collision shop repair technique. But MP&C seems like a collision man so... good info from him. I am considering a small repair in my floor pan to abate some rust using structural adhesive, rivets and a flange. No heat, and I could repair right next to the fuel tank. I am considering it for that. But then again, the floor may provide some good practice for stitch welding. I just hate to remove the fuel tank and lines.


j
__________________
White K20
jeffahart is offline   Reply With Quote
Old 05-09-2019, 10:01 PM   #16
franken
Registered User
 
Join Date: Jun 2013
Location: Somewhere
Posts: 3,124
Re: gas welding vs mig

Quote:
Originally Posted by pimpston65 View Post
has anyone used gas welding with this welding for 18g panels as well as mig welding.
No outer body panels are 18 gauge. More like 20. You and anyone else can get a caliper and measure.
Gas is less hot than arc, but regardless, you need to planish and on a fleet bed, you can't. You need really tight/cloe fit to do good gas welding, and actually want pretty close fit w/ mig/tig. Long ago, people would gas weld and planish while the weld was still red hot (hammer weld). This knocks down the weld and expands the weld that would be shrunk by the heat. It seams this was done with filler rod.

Last edited by franken; 05-10-2019 at 01:20 AM.
franken is offline   Reply With Quote
Old 05-09-2019, 10:43 PM   #17
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 8,415
Re: gas welding vs mig

pimpston65



. How is your project going?
Lot's of good idea's that was shared
in this thread you started. Thanks
I got a few idea's from this.




.
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)


http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is online now   Reply With Quote
Old 05-09-2019, 10:49 PM   #18
pimpston65
Registered User
 
pimpston65's Avatar
 
Join Date: Aug 2013
Location: corktown,mi.
Posts: 5,194
Re: gas welding vs mig

Quote:
Originally Posted by Getter-Done View Post
pimpston65



. How is your project going?
Lot's of good idea's that was shared
in this thread you started. Thanks
I got a few idea's from this.




.
its going well. im working on the complete floor pan and maybe i'll switch the firewall or patch areas of rust, at least i havent needed to much in the way of tools to get it done. finding the time is the major issue. i work alot to pay the bills and not much time for the truck, but its moving along and should have a roller soon.
pimpston65 is offline   Reply With Quote
Old 05-09-2019, 11:08 PM   #19
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 8,415
Re: gas welding vs mig

Great news.
Bills are first.
Then truck project is next to release the stress.
Keep us updated.
Have you started a build thread?
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)


http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is online now   Reply With Quote
Old 05-09-2019, 11:24 PM   #20
pimpston65
Registered User
 
pimpston65's Avatar
 
Join Date: Aug 2013
Location: corktown,mi.
Posts: 5,194
Re: gas welding vs mig

Quote:
Originally Posted by Getter-Done View Post
Great news.
Bills are first.
Then truck project is next to release the stress.
Keep us updated.
Have you started a build thread?
so true. i have one called "finally come" should have read finally came but i rushing and cant change the name...
pimpston65 is offline   Reply With Quote
Old 05-12-2019, 07:34 PM   #21
PGSigns
Senior Member
 
PGSigns's Avatar
 
Join Date: Jan 2011
Location: Hayes Va
Posts: 4,569
Re: gas welding vs mig

When I first learned to do panel repair I was helping a guy build model A's. Everything was gas welded. What I was taught was gas welding and doing it stitch and hammer. Seams were all but welded a 1/2" or so at a time and hamered when hot. Move down a foot and do it again. Once done the weld was cleaned up out came the torch and a wet rag to work the seam back flat. Same thing can be done with a mig gun and .023 wire and stich welding. Then heat and shrink. It takes practice. Google shrinking disc and watch some videos.
Jimmy
__________________
60 to 66 Chevy and GMC window decals
http://67-72chevytrucks.com/vboard/s...d.php?t=661131
Good friends, good food and a hotrod what else do you need?
1966 BBW long fleet Daily driver
1965 BBW short fleet Sold and going to a good home
1965 Suburban
2003 3500 Duramax
2005 Ultra Classic
PGSigns is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:47 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com