67-72 Gen V LT engine swap mounts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Metaltekman · 04-23-2019, 08:36 AM

METALTEK MANUFACTURING ENGINE MOUNTS
I would like to share our new Gen V LT engine mounts for the 67-72 c10 trucks

Our engine mounts do require a swap oil pan and use the high hump transmission tunnel. These are item #17050K and the transmission crossmember is #19050A

Thank you,

Jaime

**mongocanfly** · 04-23-2019, 03:59 PM

welcome....
nice brackets!
why does the pan need changed? and which pan do you need?

Metaltekman · 04-23-2019, 04:10 PM

Thanks for the reply, I appreciate it.
The L83/L86 truck pan hits the frame crossmember. For some reason the factory oil pan has a larger than normal front sump area.
I would recommend the Holley 302-20 hands down. It maintains the factory cast rigidity of the OEM pan.

cornerstone · 04-30-2019, 12:20 AM

Those mounts are the way to go!

I started on my L83 / 72 C10 swap before these were available and realized the problem of the stock truck oilpan hitting the front crossmeber. I cut pretty deep into my crossmember until it did fit, then spent way too much time welding in more steel and boxing it back together to keep it strong. I used the dirty dingo L83 adapters to work with the sbc motor mounts. They wouldn't allow space for the vacuum pump. Plus, The factory oil pan fit, but it still hung down too low for my liking.

Then, frustrated with a pieced together set up, I happened to see the weld in style Metaltek L83 mounts on eBay. These gave me a much cleaner look. I also changed over to the Holley pan and got all the ground clearance I needed.

The point is, save your time and money and buy the new Metaltek motor mounts and transmission crossmember DESIGNED for our trucks. Plus, the other guys making them are nearly 200. bucks more.

Good job Jaime at Metaltek!

Metaltekman · 05-03-2019, 12:07 AM

Thank you Cornerstone for your review, I appreciate it.

Daaaanz67 · 05-04-2019, 12:17 PM

Can you give more description on the adjustability if ther is any? Is the drop on the trans cross member lower than the bottom frame rail?

Metaltekman · 05-04-2019, 08:10 PM

Hello Daaanz67,
The plates that bolt to the engine are slider style. They give you just over an inch of front to back movement. The frame mounting portion of the mounts bolt in to the factory mounting holes.The transmission crossmember is even with the bottom of the frame rail. These mounts with the crossmember are set to the proper driveline angle. These do allow the use either stock manifolds or the Speed Engineering c10 lt headers.
Thank you for your interest,
Jaime

The Pitt · 10-09-2019, 10:00 PM

Metaltekman do the speed engineering headers hang below the frame with your mounts?

f.flujan · 10-14-2019, 11:29 PM

I used tia set up with the headers and they clear just fine. I cupped my lower control arms as well

Curt67 · 11-11-2019, 10:09 PM

Looks good! Does the factory AC and/or Alternator clear?

Can you post some more pics?

Curt67 · 11-11-2019, 11:53 PM

Looks good! Does the factory AC and/or Alternator clear?

Can you post some more pics?

04-23-2019, 03:59 PM	#2
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,670	Re: 67-72 Gen V LT engine swap mounts welcome.... nice brackets! why does the pan need changed? and which pan do you need? __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

04-23-2019, 04:10 PM	#3
Metaltekman Registered User Join Date: Mar 2019 Location: Allendale, Michigan Posts: 5	Re: 67-72 Gen V LT engine swap mounts Thanks for the reply, I appreciate it. The L83/L86 truck pan hits the frame crossmember. For some reason the factory oil pan has a larger than normal front sump area. I would recommend the Holley 302-20 hands down. It maintains the factory cast rigidity of the OEM pan.

04-30-2019, 12:20 AM	#4
cornerstone Registered User Join Date: Apr 2014 Location: Azle,Texas Posts: 2,248	Re: 67-72 Gen V LT engine swap mounts Those mounts are the way to go! I started on my L83 / 72 C10 swap before these were available and realized the problem of the stock truck oilpan hitting the front crossmeber. I cut pretty deep into my crossmember until it did fit, then spent way too much time welding in more steel and boxing it back together to keep it strong. I used the dirty dingo L83 adapters to work with the sbc motor mounts. They wouldn't allow space for the vacuum pump. Plus, The factory oil pan fit, but it still hung down too low for my liking. Then, frustrated with a pieced together set up, I happened to see the weld in style Metaltek L83 mounts on eBay. These gave me a much cleaner look. I also changed over to the Holley pan and got all the ground clearance I needed. The point is, save your time and money and buy the new Metaltek motor mounts and transmission crossmember DESIGNED for our trucks. Plus, the other guys making them are nearly 200. bucks more. Good job Jaime at Metaltek! __________________ Brian 1972 C10, "Loyd", LWB to SWB, 5.3, L83/6L80e, 4:11 Tru Trac, Air Ride, VA, DD, 20" Coys, 4 wheel disc, A quick LS swap turned into a 6 year frame off resto-mod.

05-03-2019, 12:07 AM	#5
Metaltekman Registered User Join Date: Mar 2019 Location: Allendale, Michigan Posts: 5	Re: 67-72 Gen V LT engine swap mounts Thank you Cornerstone for your review, I appreciate it.

05-04-2019, 12:17 PM	#6
Daaaanz67 Registered User Join Date: Nov 2011 Location: Idaho Posts: 857	Re: 67-72 Gen V LT engine swap mounts Can you give more description on the adjustability if ther is any? Is the drop on the trans cross member lower than the bottom frame rail?

04-23-2019, 08:36 AM	#1
Metaltekman Registered User Join Date: Mar 2019 Location: Allendale, Michigan Posts: 5	67-72 Gen V LT engine swap mounts METALTEK MANUFACTURING ENGINE MOUNTS I would like to share our new Gen V LT engine mounts for the 67-72 c10 trucks Our engine mounts do require a swap oil pan and use the high hump transmission tunnel. These are item #17050K and the transmission crossmember is #19050A Thank you, Jaime

05-04-2019, 08:10 PM	#7
Metaltekman Registered User Join Date: Mar 2019 Location: Allendale, Michigan Posts: 5	Re: 67-72 Gen V LT engine swap mounts Hello Daaanz67, The plates that bolt to the engine are slider style. They give you just over an inch of front to back movement. The frame mounting portion of the mounts bolt in to the factory mounting holes.The transmission crossmember is even with the bottom of the frame rail. These mounts with the crossmember are set to the proper driveline angle. These do allow the use either stock manifolds or the Speed Engineering c10 lt headers. Thank you for your interest, Jaime

10-09-2019, 10:00 PM	#8
The Pitt Registered User Join Date: May 2009 Location: USA Posts: 36	Re: 67-72 Gen V LT engine swap mounts Metaltekman do the speed engineering headers hang below the frame with your mounts?

10-14-2019, 11:29 PM	#9
f.flujan Registered User Join Date: Dec 2016 Location: Menifee,ca Posts: 65	Re: 67-72 Gen V LT engine swap mounts I used tia set up with the headers and they clear just fine. I cupped my lower control arms as well

11-11-2019, 10:09 PM	#10
Curt67 Registered User Join Date: Sep 2014 Location: Double Oak, TX Posts: 3	Re: 67-72 Gen V LT engine swap mounts Looks good! Does the factory AC and/or Alternator clear? Can you post some more pics?

11-11-2019, 11:53 PM	#11
Curt67 Registered User Join Date: Sep 2014 Location: Double Oak, TX Posts: 3	Re: 67-72 Gen V LT engine swap mounts Looks good! Does the factory AC and/or Alternator clear? Can you post some more pics?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.