The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-20-2019, 02:08 PM   #1
msg
Registered User
 
Join Date: Feb 2013
Location: GA
Posts: 1,315
Grease recommendations - removal and application

I have the upper and lower control arm shafts sandblasted and painted and thought to remove the gunk that is on the seals and endcaps and start fresh with new grease. I tried purple power and a brush and not a whole lotta luck, this is thick stuff.

Whats the best way to remove the existing grease and gunk and shine them up maybe?

The ball joints Ill just replace with new, but I will be needing to put some grease in them.

Should I use the same grease for both?


Also, I have a power steering unit that I would like to spruce up.

Any recommendations on what to do...and what not to do as well?
Attached Images
   
__________________
Progress thread for my 66
http://67-72chevytrucks.com/vboard/s...d.php?t=623848
msg is offline   Reply With Quote
Old 09-20-2019, 04:16 PM   #2
The Rocknrod
Moderator

 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
Re: Grease recommendations - removal and application

What I would do is - Mineral Spirit is good, dry cleaning solvent is more refined. Any more refined my damage any seals.
Seal up the inlet/outlet of the power steering box. If it doesn't need a rebuild or replace - Clean the grease off with mineral spirit. Then wire wheel the unit clean and spray paint it.
Opinions may vary.
The Rocknrod is offline   Reply With Quote
Old 09-20-2019, 09:38 PM   #3
bama63
Registered User
 
bama63's Avatar
 
Join Date: Jun 2010
Location: gadsden, alabama
Posts: 468
Re: Grease recommendations - removal and application

scrape off heavy stuff, spray with oven cleaner let stand and hose off, let dry and paint. works like a charm
__________________
Due to financial constraints, the light at the end of the tunnel will be shut off until further notice
bama63 is offline   Reply With Quote
Old 09-21-2019, 12:16 AM   #4
Captainfab
60-66 Nut

 
Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,252
Re: Grease recommendations - removal and application

I agree with mineral spirits, cleaning solvent. Diesel fuel works pretty good too.
__________________
Power Steering Box Adapter Plates For Sale HERE
Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE
Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE
Hydroboost Mounting Plates HERE
Captainfab is offline   Reply With Quote
Old 09-21-2019, 10:00 PM   #5
AcampoDave
Registered User
 
AcampoDave's Avatar
 
Join Date: Feb 2013
Location: central California
Posts: 2,776
Re: Grease recommendations - removal and application

"Dawn takes grease out of your way"
GoJo waterless hand cleaner works good too. I've cleaned some nasty grease caked stuff with either of them in combination with a metal garden hose pistol and a brush. (Provided of course the parts in question can tolerate water)

Last edited by AcampoDave; 09-21-2019 at 10:09 PM.
AcampoDave is offline   Reply With Quote
Old 09-22-2019, 02:49 PM   #6
vince1
Registered User
 
Join Date: Jan 2013
Location: Calgary Alberta
Posts: 1,170
Re: Grease recommendations - removal and application

I like to use the black grease with molybdenum disulphide in it. You won't wear out any parts using that stuff. Caterpillar recommends it.
vince1 is offline   Reply With Quote
Old 09-22-2019, 11:29 PM   #7
msg
Registered User
 
Join Date: Feb 2013
Location: GA
Posts: 1,315
Re: Grease recommendations - removal and application

Thanks guys, I have mineral spirits and will try that. Ive been using some ragged out micro fiber towels and the purple power and its gonna take something stronger.


On the grease to add in once the caps and seals are cleaned, I had used this Lucas Oil xtra heavy duty grease in some ball joints I installed in another car.

https://shop.advanceautoparts.com/p/...ontent=general

It was recommended at the time by a local mechanic, but I was looking at the grease in these caps and its a different looking grease.

On the molybdenum disulphide, I saw this on a quick search

https://shop.advanceautoparts.com/p/...B&gclsrc=aw.ds

even this from HF

https://www.harborfreight.com/sta-lu...saAjKuEALw_wcB
__________________
Progress thread for my 66
http://67-72chevytrucks.com/vboard/s...d.php?t=623848
msg is offline   Reply With Quote
Old 09-22-2019, 11:46 PM   #8
Captainfab
60-66 Nut

 
Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,252
Re: Grease recommendations - removal and application

For the past 5 years I have been using Lucas red n tacky grease on the fleet of semi trucks and trailers that I service. I am pleased with it and have had no failures of the greased parts.
__________________
Power Steering Box Adapter Plates For Sale HERE
Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE
Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE
Hydroboost Mounting Plates HERE
Captainfab is offline   Reply With Quote
Old 09-23-2019, 07:49 AM   #9
The Rocknrod
Moderator

 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
Re: Grease recommendations - removal and application

Quote:
Originally Posted by vince1 View Post
I like to use the black grease with molybdenum disulphide in it. You won't wear out any parts using that stuff. Caterpillar recommends it.
I use that stuff from a small tub on my wheel bearings since 1979.
The Rocknrod is offline   Reply With Quote
Old 09-29-2019, 03:23 PM   #10
msg
Registered User
 
Join Date: Feb 2013
Location: GA
Posts: 1,315
Re: Grease recommendations - removal and application

The mineral spirits worked perfect, toothbrush and 3m scrub pad and steel wool. I got them all but 1 in good shape, it was missing the fitting at the top and was pretty badly rusted inside. I kept scrubbing and the brown color of the grease turned a rusty color. Looks like I need to find a replacement now.
Attached Images
   
__________________
Progress thread for my 66
http://67-72chevytrucks.com/vboard/s...d.php?t=623848
msg is offline   Reply With Quote
Old 01-17-2020, 01:41 PM   #11
Mike_The_Grad
Senior Member
 
Mike_The_Grad's Avatar
 
Join Date: Oct 2013
Location: Santa Paula, CA
Posts: 630
Re: Grease recommendations - removal and application

If you plan on cleaning up the power steering gear box you can wire wheel it the best you can. Then switch to a dremel with wire wheel attachment, or a cordless power drill with wire wheel bits. You can get em in flat, cupped, or straight styles. Then wipe it down with acetone or mineral spirits and once it dries hit it with a couple of coats of clear coat from a rattle can. I like the VHT clear coat. It's better suited to the environment where the gear box resides. That way it wont rust on you, and if you have a power steering or radiator leak it wont seep into the cast iron body of the gear box. So itll stay nice and clean longer. As far as grease for the control arm shafts goes, I used Timken wheel bearing grease when I replaced my stock arm shafts with MOOG. Comes in a tub. But any chassis/suspension grade grease will do fine. Here's a tip for reassembly. Pack the control arm shafts end caps with grease before screwing them onto the shafts. Leave the zerk fitting off until you get the end caps torqued in place, that way the excess grease will squeeze out of the end cap when you screw them on. Then install the zerk afterwards. That's how I did mine and I haven't had to grease them since I installed them a few months ago.
Also, if you haven't already I would upgrade your lower control arm shaft u bolts to the bigger 9/16" ones from the later year pickups. Dorman part #13503 available at AutoZone $10 for a set of 2. Need 2 sets. Also need to drill out the crossmember u bolt holes to 9/16" and they slide right in. Bigger,stronger,better.
__________________
1972 C/10 LWB - Mine
1964 C/10 LWB - My Dad's

Instagram: Mike_The_Grad
Mike_The_Grad is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:19 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com