The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1969 - 1972 Blazers and Jimmys Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-04-2019, 10:25 AM   #1
C.I.Blazer
Registered User
 
Join Date: Aug 2019
Location: WA State
Posts: 186
Boyds EFI Tank Install Questions

Hoping for some help on the installation of a Boyd's EFI Tank. I have tried searching but have not been able to find the answers. i think I am clear on mounting the tank and running the fuel lines, my questions is on ventilation. The tank comes with one vent (and an optional roll over vent). What do I hook this vent up to? Is it the ventilation line that attaches to the top of the fuel filler neck? I also have the two vent lines from the old tank that hook to the vapor recovery system and up to the charcoal canister. Do I still use this system with a modern EFI setup or do I pull all this out?

In regards to wiring, I am planning on running a 12 gauge hot and ground for the pump up the frame rail to the engine compartment and also another 12 gauge line for the sender. Is that correct?

Thanks for the help!
C.I.Blazer is offline   Reply With Quote
Old 10-04-2019, 01:00 PM   #2
notsolo
Registered User
 
notsolo's Avatar
 
Join Date: Apr 2008
Location: Md
Posts: 2,482
Re: Boyds EFI Tank Install Questions

I have a Boyd EFI tank, Bought a rollover vent for it, not connected to anything. The original Blazer vent stack was not used. I used a charcoal canister mounted on the drivers side up front, fuel line and return on the passenger side. Pump is in the tank.
notsolo is offline   Reply With Quote
Old 10-05-2019, 07:18 AM   #3
C.I.Blazer
Registered User
 
Join Date: Aug 2019
Location: WA State
Posts: 186
Re: Boyds EFI Tank Install Questions

Thanks Notsolo! So you did not use the vent line that is part of the filler neck? Also, any insight on the wiring?

I am trying to get some wiring and plumbing lines in place before the tank arrives and this is really helpful. Good to know I do not need to the old vapor recovery stack.

Thanks again!
C.I.Blazer is offline   Reply With Quote
Old 10-05-2019, 04:46 PM   #4
jaros44sr
Senior Member
 
jaros44sr's Avatar
 
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,762
Re: Boyds EFI Tank Install Questions

Don't you need a relay? so no sparks at pump
__________________
Semper Fi...Uncle Sam, you da man

All parts offered to help are free, unless otherwise noted

Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training
SAFETY FIRST

AS usual, off topic

They say your mind goes second, can't remember the first


Jim
jaros44sr is offline   Reply With Quote
Old 10-06-2019, 06:58 AM   #5
C.I.Blazer
Registered User
 
Join Date: Aug 2019
Location: WA State
Posts: 186
Re: Boyds EFI Tank Install Questions

Yes! Thanks jarros44sr. I have now learned 12v wire from pump+ to relay in the engine compartment, ground from pump- to frame, and single wire from sending unit to gauge.

Still trying to understand how the vent next to the filler tube works...

Thought I would try and get all the wires and tubing run before I re-install the engine and transmission so access is easier.
C.I.Blazer is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:32 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com