The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-10-2020, 04:21 PM   #1
Nick_R_23
Registered User
 
Nick_R_23's Avatar
 
Join Date: May 2016
Location: Willow, Alaska
Posts: 881
Considering running 18’s - what fits?

I have a 1986 GMC C1500 LWB that’s lowered 4.5/6” on stock rally wheels. I ran across a decent deal on a set of 18” wheels that may potentially fit on the truck. It has 235/70R15’s on it now, and the new wheels would be staggered, but I’m waiting to hear the exact specs on them. The tires are 245/55R18 and 295/45R18, so diameter would be very close and I know the widths would be a sure fit. For those of you that have went the 18” route, what specs did you end up with for your wheels to fit? I don’t want any modifications or rubbing.
Nick_R_23 is offline   Reply With Quote
Old 09-12-2020, 02:45 PM   #2
Nick_R_23
Registered User
 
Nick_R_23's Avatar
 
Join Date: May 2016
Location: Willow, Alaska
Posts: 881
Re: Considering running 18’s - what fits?

Alright, so the specs on these are 18x9.5, ET12 on all four wheels.
Nick_R_23 is offline   Reply With Quote
Old 09-13-2020, 10:24 PM   #3
Nick_R_23
Registered User
 
Nick_R_23's Avatar
 
Join Date: May 2016
Location: Willow, Alaska
Posts: 881
Re: Considering running 18’s - what fits?

Nobody knows if 18x9.5 with 5.75” backspacing will fit on all four corners?
Nick_R_23 is offline   Reply With Quote
Old 09-13-2020, 10:31 PM   #4
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,711
Re: Considering running 18’s - what fits?

the 18 isn't an issue but the 9.5 is going to put part of the tread of the tire outside the wheel well unless the wheels are offset to the inside.
It isn't the wheel diameter near as much as the rim width and the offset that you have to deal with.
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 09-13-2020, 11:06 PM   #5
Nick_R_23
Registered User
 
Nick_R_23's Avatar
 
Join Date: May 2016
Location: Willow, Alaska
Posts: 881
Re: Considering running 18’s - what fits?

That’s really what I’m having trouble finding is the offset specs. I’ve found a few older posts with 9.5” rims on the front, but not a single one lists the offset or backspacing that was used.
Nick_R_23 is offline   Reply With Quote
Old 09-13-2020, 11:24 PM   #6
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,732
Re: Considering running 18’s - what fits?

There’s some info here to figure out your bs using a chunk of angle iron and reddy rod.


https://www.hotrod.com/articles/ccrp...heels-fitment/

Or you can buy a nicer tool to be more accurate.


https://www.speedwaymotors.com/Percy...rite,6761.html
geezer#99 is online now   Reply With Quote
Old 09-14-2020, 10:38 AM   #7
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
Re: Considering running 18’s - what fits?

You can also measure your current wheels installed & do calculations off of them.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Old 09-15-2020, 02:41 AM   #8
Nick_R_23
Registered User
 
Nick_R_23's Avatar
 
Join Date: May 2016
Location: Willow, Alaska
Posts: 881
Re: Considering running 18’s - what fits?

Main problem is that I’m away for work for a while and don’t/haven’t had access to my truck for a while. I’d rather not guess on a fitment as wheels aren’t cheap.

However, since nobody seems to know for sure, I tried to do a little more research. Let’s see if you all agree with what I came up with.

I found a 15x8 rally wheel has 4” backspacing (and also 4” frontspacing). These 9.5” wheels have 5.75” backspacing (and 3.75” frontspacing). This means the new wheel will sit inward only .25” on the outside, but 1.75” inward more on the inside. However, with a 1” wheel spacer, it would now center the backspacing like stock (with 4.75” on each side now), but the wheel would be 3/4 wider than stock on both the inside and the outside of the wheel.

So the big question would be, do I have enough room on both the inside and outside of the wheel to add an extra 3/4” width each direction over a stock 15x8?
Nick_R_23 is offline   Reply With Quote
Old 09-15-2020, 09:02 AM   #9
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,732
Re: Considering running 18’s - what fits?

Quote:
Originally Posted by Nick_R_23 View Post
Main problem is that I’m away for work for a while and don’t/haven’t had access to my truck for a while. I’d rather not guess on a fitment as wheels aren’t cheap.

However, since nobody seems to know for sure, I tried to do a little more research. Let’s see if you all agree with what I came up with.

I found a 15x8 rally wheel has 4” backspacing (and also 4” frontspacing). These 9.5” wheels have 5.75” backspacing (and 3.75” frontspacing). This means the new wheel will sit inward only .25” on the outside, but 1.75” inward more on the inside. However, with a 1” wheel spacer, it would now center the backspacing like stock (with 4.75” on each side now), but the wheel would be 3/4 wider than stock on both the inside and the outside of the wheel.

So the big question would be, do I have enough room on both the inside and
outside of the wheel to add an extra 3/4” width each direction over a stock 15x8?
Your numbers are skewed.
An 8 inch rim is actually 9 inches wide from edge to edge. So with 4 inch bs you have 5 inch front space. Back spacing is measured from the edge to the wheel mount surface.
When you figure measurements remember tire cross section (Bulge)which generally is 1 inch wider than the rim.
And then you need 1 inch clearance beyond edge of tire to anything it might rub on.
It gets real complicated.
Much easier to make or buy a tool like I linked and be accurate.
Some might think an 80 buck tool is a waste of money but you’ll use it more than once.this won’t be the only time you try to stuff your wheel wells with lots of rubber.
geezer#99 is online now   Reply With Quote
Old 09-15-2020, 10:15 AM   #10
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
Re: Considering running 18’s - what fits?

Quote:
Originally Posted by Nick_R_23 View Post
Main problem is that I’m away for work for a while and don’t/haven’t had access to my truck for a while. I’d rather not guess on a fitment as wheels aren’t cheap.

However, since nobody seems to know for sure, I tried to do a little more research. Let’s see if you all agree with what I came up with.

I found a 15x8 rally wheel has 4” backspacing (and also 4” frontspacing). These 9.5” wheels have 5.75” backspacing (and 3.75” frontspacing). This means the new wheel will sit inward only .25” on the outside, but 1.75” inward more on the inside. However, with a 1” wheel spacer, it would now center the backspacing like stock (with 4.75” on each side now), but the wheel would be 3/4 wider than stock on both the inside and the outside of the wheel.

So the big question would be, do I have enough room on both the inside and outside of the wheel to add an extra 3/4” width each direction over a stock 15x8?
Ahh . . ….. Not having things in front of you does make it difficult to accurately measure. The issue is when others declare something 'clears just fine', it's doing so on a different truck w/possibly a different group of parts & from a different perspective. What one guy is ok with, another may not care for.

It sounds like you're buying 'off the shelf' wheels vs. custom spec (choosing the exact BS/offset) based on the wheel size/BS listed. I really suggest waiting until you can measure in-person. It's a hard choice to have to wait but a better choice unless you can easily buy/return the wheels until you get what you want.

Most guys like the 15x8 w/4"BS factory look. The 9.5" size you listed will be tucked in more but you'll adjust for that w/spacers. That means testing lock-to-lock turning to verify clearance up front because they're still going to be closer to the suspension parts (farther-out because of larger wheel diameter but still farther in-board as far as distance vs the current wheel).

I'm guessing your current set-up clears the fender lip. Your proposed 9.5's would be .750 farther out vs your current set-up. Does it clear by that much?

Now lets move to the rear.....

A 10" wheel w/5" of back spacing is centered in the wheel well & has about the same clearance inside & out from contacting sheet metal. A 10" wheel w/5.5BS starts getting real close to the inner tub.

If your current 8's clear fine, the proposed 9.5's are 1.75" farther in-board vs the Ralley. The 1" spacer here will keep the wheel from buzzing on the inside @ the tub.

In theory (math), they'll clear F&R. They'll have the 'look' that a FWD does or like the late models do w/minimal lip on the outer edge vs. the current steel wheels you have.
The current track width phenomenon (front slightly wider vs rear) might be more pronounced as well.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.

Last edited by SCOTI; 09-15-2020 at 10:21 AM.
SCOTI is offline   Reply With Quote
Old 09-15-2020, 11:10 AM   #11
Nick_R_23
Registered User
 
Nick_R_23's Avatar
 
Join Date: May 2016
Location: Willow, Alaska
Posts: 881
Re: Considering running 18’s - what fits?

Yes, I found some off the shelf wheels that I think would be a great look. I usually do stick with the classic 15x8, but I thought I might switch it up this time. They’re far cheaper than new, but not cheap enough to pull the trigger on without knowing, since they wouldn’t be easy to resell up here.

The current setup (15x8, 235/70R15, 4.5” drop) clears excellent, but it’s honestly not that much tire up front. My previous truck was the same, except with a 255/60R15 tire, and I never had any clearance issues - I just don’t remember how much clearance the rim/tire had in relation to the fender. I am also taking into account that the front track width grows when lowered too.
Nick_R_23 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:53 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com