The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > LSx Swaps

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-30-2020, 05:45 PM   #1
Pitpig
Registered User
 
Join Date: Jan 2019
Location: Bonner Springs, KS
Posts: 56
Ground the PCM

Went for my first start today with 5.3 swap homemade harness. Dead with no fuel pump kick on. I imagined the worst, did the harness myself with lt1swap instructions. Read on another sight to ground the pcm case. It fired right up
Pitpig is offline   Reply With Quote
Old 10-30-2020, 09:37 PM   #2
Captainfab
60-66 Nut

 
Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,252
Re: Ground the PCM

Thanks for the insight.
__________________
Power Steering Box Adapter Plates For Sale HERE
Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE
Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE
Hydroboost Mounting Plates HERE
Captainfab is offline   Reply With Quote
Old 10-30-2020, 10:23 PM   #3
clinebarger
Senior Member
 
Join Date: May 2009
Location: Fort Worth, TX
Posts: 6,370
Re: Ground the PCM

The PCM body doesn't need to be grounded......If it did, You're missing ground connection somewhere.
clinebarger is offline   Reply With Quote
Old 10-31-2020, 04:18 PM   #4
LS short box
Registered User
 
Join Date: Jun 2015
Location: Carlos MN
Posts: 2,132
Re: Ground the PCM

I've never grounded the case of the PCM on my LS swaps. But I've never built a harness myself. Always purchased the PCM and harness from the same supplier.
LS short box is offline   Reply With Quote
Old 11-01-2020, 07:35 PM   #5
Pitpig
Registered User
 
Join Date: Jan 2019
Location: Bonner Springs, KS
Posts: 56
Re: Ground the PCM

Now that I think of it, there were a few stray ground wires not accounted for, but grounding the case fixed it
Pitpig is offline   Reply With Quote
Old 11-01-2020, 10:25 PM   #6
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,670
Re: Ground the PCM

With a LS swap, the more grounds the merrier...
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 11-02-2020, 09:31 PM   #7
truckdude239
Senior Member
 
truckdude239's Avatar
 
Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,237
Re: Ground the PCM

I had to do the same thing on my swap about 300 miles into swap I had lot of run issuses turns out I never bolted the grounds to back of the head and they where touching hit a bump lost ground I felt like an idiot but never went back and ungrounded the pcm
__________________
David fuller
Ase Certified Mechanic
Click here to help support our board!!


1971 Chevy c-10 under going a 4.8l LSx swap

Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305

2007 Honda Accord my daily 145kmiles
2002 Honda Accord 4 door With 330k(sisters car)
2005 toyota Avalon 228k( brothers car)
2002 Sububran 5.3 245k
2000 Tahoe 5.3l 378

General manager for Marco's Carwash & lube
truckdude239 is offline   Reply With Quote
Old 11-02-2020, 10:36 PM   #8
LS short box
Registered User
 
Join Date: Jun 2015
Location: Carlos MN
Posts: 2,132
Re: Ground the PCM

As said above Ls swaps love good clean grounds. Main ground cable from the battery I run the 00 gauge cable directly to the engine block. Then on each side of the engine block back to the frame. Similar size cable. I try to hide them. If you have any paint on the block make sure you sand down to good metal. Star lock washers help bite into the head bolt holes.
LS short box is offline   Reply With Quote
Old 11-03-2020, 12:02 AM   #9
87chevy.com
BMW & ASE Master Certified
 
87chevy.com's Avatar
 
Join Date: Feb 2004
Location: Houston, Texas
Posts: 1,266
Re: Ground the PCM

Quote:
Originally Posted by Pitpig View Post
Now that I think of it, there were a few stray ground wires not accounted for, but grounding the case fixed it
think it masks the problem of a missing ground... more than likely, something that's needing ground is going through a path its not designed for...

if that's the case, your going to be creating problems thats going to be hard to trouble shoot over the web....
__________________
1987 Silverado - L83 5.3 w/ 6L80e ,A/C,P/W,P/L,TILT, HID projectors, Wilwood C-10 Pro Spindles w/ 2018 silverado front brakes & C-5 Corvette Rear Disc Brakes
1999 BMW 528i - 5.7 LS1 w/ 4l60e, Ford 8.8 IRS w31 spline posi & FX-r projector retrofit

New project: 2006 BMW x5 6cyl AWD to L83 6l80e 4wd to 2WD / RWD

A poor man buy's it twice

finally got my domain name back, 87chevy.com.... site rework in progress
87chevy.com is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:08 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com