The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-27-2021, 10:07 PM   #1
karlbenz
Registered User
 
Join Date: Nov 2008
Location: kannapolis, nc
Posts: 528
10 bolt issues

got a leaking wheel seal. pulled differential cover. carrier pin bolt came out with no issue. carrier pin is giving me lots of trouble. won't budge one way and I can get about 1/2" the other way (with a lot of persuasion). any tricks for this?
__________________
2000 c3500 utility bed 7.4l 5sp manual old body style. Cab and chassis
1964 GMC K10 383cu in/sm465/twin stick np205
1965 Chevy C60
karlbenz is offline   Reply With Quote
Old 05-28-2021, 11:24 AM   #2
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,634
Re: 10 bolt issues

Work it back and forth then grab it with a pair of vice grips...this must have a posi?
kwmech is offline   Reply With Quote
Old 05-28-2021, 04:50 PM   #3
karlbenz
Registered User
 
Join Date: Nov 2008
Location: kannapolis, nc
Posts: 528
Re: 10 bolt issues

Quote:
Originally Posted by kwmech View Post
Work it back and forth then grab it with a pair of vice grips...this must have a posi?
wouldn't budge going the other way. still could only get about a 1/2" today. finally quit and put it back together for another day. needed to get to work on the front springs and shocks.
it's not a posi. I was actually gonna put a lunchbox locker in it while I was in there.
I've never had this trouble with a pin before. usually slide out with very little work
__________________
2000 c3500 utility bed 7.4l 5sp manual old body style. Cab and chassis
1964 GMC K10 383cu in/sm465/twin stick np205
1965 Chevy C60
karlbenz is offline   Reply With Quote
Old 05-28-2021, 09:14 PM   #4
Ziegelsteinfaust
Registered User
 
Join Date: Dec 2012
Location: Temple City
Posts: 3,628
Re: 10 bolt issues

Some times they wobble the hole out in such a way that they get stuck.

This happened to a 8.8 I shortened for a guy. I end up heating the carrier a bit to grow the tolerances, and then beat it like it owed me money.

I did it on a bench which gave me more leverage
Ziegelsteinfaust is offline   Reply With Quote
Old 05-29-2021, 10:57 AM   #5
Pontiac1976
Registered User
 
Pontiac1976's Avatar
 
Join Date: Oct 2015
Location: Ottawa, Ontario, Canada
Posts: 766
Re: 10 bolt issues

Stupid question does your pin have a small screw bolt in the area (center) of the pin ( some have screw helps hold the pin from sliding passed it. The screw think it a 3/8" head or reverse torque head. ) Once the screw out the pin slide much easier.
__________________
1977 REG cab Long Bed with a 1984 Front Clip, 82 305 .60 over 9.0.1 flat top pistons, 4bbl, TH350, w/84 SS-intake & cam , w/ 1977 big block rad, 1975 gear box, 1984 master w/ metric fittings top & SAE fitting @ portion block, 1975 3.42 gear open diff. Duel 77-87 Factory air cleaner, duel inlet from rad support . Down sized 9' to new 8' Steel flat bed
Was a 77 454 w/308 gear. Taken out 550 lbs. up front with motor clip change.
Pontiac1976 is offline   Reply With Quote
Old 05-29-2021, 12:46 PM   #6
84 400
Sb 400 club
 
84 400's Avatar
 
Join Date: Nov 2005
Location: NH / MA
Posts: 2,746
Re: 10 bolt issues

Did the retaining bolt break? I had that happen on a coperate 10 bolt front in my 77. The threaded part came out but part of the retaining bolt was left in the slit. Fished it out and got the pin out.

Is this a front or rear? If its a front and you can pull the axle ahafts i would just pull the carrier and deal with it on the bench. If its a C clip rear…

Diregard that leaking wheel seal it muat be a rear then
__________________
1984 chevy c10, built 400sb,.(SOLD)
77 K10 Project / daily driver "The Grinch" http://67-72chevytrucks.com/vboard/s...d.php?t=318363
1956 Willys Wagon (327 chevy) Project (Now Buick 225)
1980 Corvette L-48 4 speed
1992 Mustang GT built 5.0 5 speed

1985 C10 LWB Sold
1982 K10 SWB plow truck Parted out
1986 D30 M1028 fire brush truck Parted out
84 400 is offline   Reply With Quote
Old 05-29-2021, 04:14 PM   #7
karlbenz
Registered User
 
Join Date: Nov 2008
Location: kannapolis, nc
Posts: 528
Re: 10 bolt issues

The retaining bolt came out in one piece
__________________
2000 c3500 utility bed 7.4l 5sp manual old body style. Cab and chassis
1964 GMC K10 383cu in/sm465/twin stick np205
1965 Chevy C60
karlbenz is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:04 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com