The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-04-2021, 09:48 AM   #1
eric8
Registered User
 
Join Date: May 2013
Location: Utopia
Posts: 216
Seat edge support springs

My seat is collapsing on the drivers edge and I can feel wire poking through, which I’m assuming is one of the seat edge springs as shown in the LMC diagram (item #4). Anyone replaced these before? How many are used per side? Can they be replaced from the bottom without removing the upholstery? I haven’t had the chance to pull my seat out yet and it’s hard to see up under there. Thanks!
Attached Images
 
eric8 is offline   Reply With Quote
Old 09-04-2021, 12:40 PM   #2
Pontiac1976
Registered User
 
Pontiac1976's Avatar
 
Join Date: Oct 2015
Location: Ottawa, Ontario, Canada
Posts: 766
Re: Seat edge support springs

Look up TKCR She does seat on the board. Her work topnotch
__________________
1977 REG cab Long Bed with a 1984 Front Clip, 82 305 .60 over 9.0.1 flat top pistons, 4bbl, TH350, w/84 SS-intake & cam , w/ 1977 big block rad, 1975 gear box, 1984 master w/ metric fittings top & SAE fitting @ portion block, 1975 3.42 gear open diff. Duel 77-87 Factory air cleaner, duel inlet from rad support . Down sized 9' to new 8' Steel flat bed
Was a 77 454 w/308 gear. Taken out 550 lbs. up front with motor clip change.
Pontiac1976 is offline   Reply With Quote
Old 09-04-2021, 12:43 PM   #3
Pontiac1976
Registered User
 
Pontiac1976's Avatar
 
Join Date: Oct 2015
Location: Ottawa, Ontario, Canada
Posts: 766
Re: Seat edge support springs

http://67-72chevytrucks.com/vboard/s...d.php?t=715398http://67-72chevytrucks.com/vboard/s...d.php?t=715398
__________________
1977 REG cab Long Bed with a 1984 Front Clip, 82 305 .60 over 9.0.1 flat top pistons, 4bbl, TH350, w/84 SS-intake & cam , w/ 1977 big block rad, 1975 gear box, 1984 master w/ metric fittings top & SAE fitting @ portion block, 1975 3.42 gear open diff. Duel 77-87 Factory air cleaner, duel inlet from rad support . Down sized 9' to new 8' Steel flat bed
Was a 77 454 w/308 gear. Taken out 550 lbs. up front with motor clip change.
Pontiac1976 is offline   Reply With Quote
Old 09-04-2021, 01:05 PM   #4
Pitpig
Registered User
 
Join Date: Jan 2019
Location: Bonner Springs, KS
Posts: 56
Re: Seat edge support springs

I’ve replaced them, I think it comes with one per side. My problem was the outer horizontal spring was broken in several places. You can probably pull upholstery back, fix spring and hog ring or clip back
Pitpig is offline   Reply With Quote
Old 09-04-2021, 01:56 PM   #5
TKCR
Senior Member
 
TKCR's Avatar
 
Join Date: Oct 2014
Location: Ohio
Posts: 6,979
Re: Seat edge support springs

They do only come 1 per side, but you can add up to 3 per side. I do 2 per side. And it’s almost impossible to replace these, unless the seat is completely torn down and the foam is removed. And there’s no hog ringing a broken spring. I have seen so many jimmy jack repairs when it comes to these broken springs. Fix the things the right way, install new springs.
This what I see the most, people but a block of foam in there. Again, you go to all the trouble of stripping the seat, then why not fix it right.
Attached Images
     
TKCR is offline   Reply With Quote
Old 09-05-2021, 08:18 AM   #6
Pitpig
Registered User
 
Join Date: Jan 2019
Location: Bonner Springs, KS
Posts: 56
Re: Seat edge support springs

Was probably unclear there, hog ring the upholstery back after fixing the springs. You can make the spring yourself with right gauge wire. Not restoring a rolls here and jimmy-jacking is an American tradition
Pitpig is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:10 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com