The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-31-2021, 06:34 PM   #1
AcampoDave
Registered User
 
AcampoDave's Avatar
 
Join Date: Feb 2013
Location: central California
Posts: 2,776
Front Bed Panel Swap

Anyone ever try to it without moving the bed back? I'm gonna change mine if there's not a lot of heavy lifting involved. Thanks
AcampoDave is offline   Reply With Quote
Old 10-31-2021, 10:38 PM   #2
cwcarpenter98
Senior Member


 
cwcarpenter98's Avatar
 
Join Date: Jan 2018
Location: Hickory Flat, GA
Posts: 4,488
Re: Front Bed Panel Swap

Fleetside?

When I was pulling the bed apart to swap sides on my truck, I had to pretty much remove one side to even think about getting the front off. It was a struggle for me.
The way the bedsides go over the top of the front panel and the front panel sits inside the front bedside flanges on the fleetside make it to where it's easier to just remove one bedside
__________________
Christian Carpenter

1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive
Overdrive wiring here
1963-ish truck bed trailer - Half-Wit

1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed

1995 Dodge Dakota Sport

"I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson
cwcarpenter98 is offline   Reply With Quote
Old 10-31-2021, 10:44 PM   #3
AcampoDave
Registered User
 
AcampoDave's Avatar
 
Join Date: Feb 2013
Location: central California
Posts: 2,776
Re: Front Bed Panel Swap

Yes, fleetside. Removing one side is do-able since the bolts are still pretty fresh from re-doing the wood. Thanks
AcampoDave is offline   Reply With Quote
Old 10-31-2021, 10:47 PM   #4
cwcarpenter98
Senior Member


 
cwcarpenter98's Avatar
 
Join Date: Jan 2018
Location: Hickory Flat, GA
Posts: 4,488
Re: Front Bed Panel Swap

You're welcome! A second helper is extremely nice to have when going back together, especially on a long bed


Edit to add: I left the front panel on when I was doing my swap, but would have been real easy to change that out without moving the whole bed back when I was at this point
Attached Images
 
__________________
Christian Carpenter

1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive
Overdrive wiring here
1963-ish truck bed trailer - Half-Wit

1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed

1995 Dodge Dakota Sport

"I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson
cwcarpenter98 is offline   Reply With Quote
Old 10-31-2021, 10:55 PM   #5
AcampoDave
Registered User
 
AcampoDave's Avatar
 
Join Date: Feb 2013
Location: central California
Posts: 2,776
Re: Front Bed Panel Swap

The pic sums it up pretty well. I got a helper and a soft front lawn to set it down on so I guess I'm good to go.
AcampoDave is offline   Reply With Quote
Old 11-02-2021, 07:08 PM   #6
wizard3354
Registered User
 
Join Date: Feb 2013
Location: Columbus, IN
Posts: 5
Re: Front Bed Panel Swap

I just did this to mine. After unbolting the bed panel, I removed the bedside Bolts going back to the wheel wells on both sides. This gave me enough wiggle room to pull the front of the besides out, lay the front bed panel down, and then pull it out. Putting the new one in is just the reverse. Hope that helps.
wizard3354 is offline   Reply With Quote
Old 11-02-2021, 10:19 PM   #7
AcampoDave
Registered User
 
AcampoDave's Avatar
 
Join Date: Feb 2013
Location: central California
Posts: 2,776
Re: Front Bed Panel Swap

^^ that's starting to sound like a one man operation. I'll give it a try. I'm gonna paint it this weekend and we'll see how it goes next weekend after. Thanks
AcampoDave is offline   Reply With Quote
Old 11-14-2021, 10:45 PM   #8
AcampoDave
Registered User
 
AcampoDave's Avatar
 
Join Date: Feb 2013
Location: central California
Posts: 2,776
Re: Front Bed Panel Swap

Thanks for the replys. I ended up loosening both sides all the way back to just behind the wheel tubs. I also loosened where the tubs rest on the wood and removed the 4 "kickstands" underneath. The sides pulled away easily enough and the tubs being still bolted to the bedsides kept them from falling down. I layed the new panel down flat on the floor and it just lifted right up into place.
AcampoDave is offline   Reply With Quote
Old 11-14-2021, 10:49 PM   #9
cwcarpenter98
Senior Member


 
cwcarpenter98's Avatar
 
Join Date: Jan 2018
Location: Hickory Flat, GA
Posts: 4,488
Re: Front Bed Panel Swap

Good deal. Thanks for updating us
__________________
Christian Carpenter

1963 C10 - Frankentruck 283, Muncie 3 speed with overdrive
Overdrive wiring here
1963-ish truck bed trailer - Half-Wit

1981 C10 - Penny 305, th350 --> Soon to be 350, Saginaw 4 speed

1995 Dodge Dakota Sport

"I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson
cwcarpenter98 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:50 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com