Floorboards and wire harness??? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

MASTERBrian · 01-12-2023, 03:03 PM

My outer rockers are good condition, but I do need new floor pans in my 1960 Suburban. I can get pics if needed, but they are shot to the kickpanel on the sides. I believe the tunnel is fine.

Is it best to just buy the individual sides or the entire floor section? And where would you buy them from?

On that note, I need to re-wire the interior (could do engine bay as well, but I cleaned that up when I got her running). What's the best harness to get?

Then to combine these, has anyone ripped out the floor pans, then re-wired using the nice large holes in the floor to get up into the dash from underneath? I have a 4 post lift, so I'm thinking if tough to get under the dash, that might make it easier. Is that a crazy idea? Would it even work?

62c30 · 01-12-2023, 11:08 PM

I pieced in places on my 61 truck, if I could redo it I would have done a one piece floor. I have not used a one piece floor so I don't know on the brands. I'm sure it's like every other aftermarket sheet metal and will probably need some work. I usually buy from LMC and classic parts. LMC gives a discount if you order the day before and pick up in person.

**The Rocknrod** · 01-13-2023, 07:28 AM

I found it pretty easy to wire the cab/dash with the seat out. I also removed the gauge panel and wired everything so that I could plug it all in when I re-installed it.

**Winchrig** · 01-13-2023, 11:05 AM

I just redid the wiring harness in my 65 gmc 5000 last summer. I got a universal GM wiring harness through painless wiring. It was super easy, all the wires were labeled and it came with a detailed instruction book.

Arne · 01-13-2023, 12:07 PM

I replaced most all of the wiring on my '64 with harnesses from American Autowire. They have stock restoration harnesses, update harnesses with more circuits, and full custom kits. I used stock restoration kits, but with a couple of custom options for passenger-side alternator and HEI. Pretty much plug and play. I've linked their website, but their products can be bought from other suppliers as well, sometimes a couple of bucks cheaper.

https://www.americanautowire.com/

**jweb** · 01-13-2023, 12:38 PM

The floor of the suburban is different than the trucks. So depending on where your issues are you may be piecing it anyway.

01-12-2023, 03:03 PM	#1
MASTERBrian Registered User Join Date: Jan 2017 Location: Wichita Posts: 639	Floorboards and wire harness??? My outer rockers are good condition, but I do need new floor pans in my 1960 Suburban. I can get pics if needed, but they are shot to the kickpanel on the sides. I believe the tunnel is fine. Is it best to just buy the individual sides or the entire floor section? And where would you buy them from? On that note, I need to re-wire the interior (could do engine bay as well, but I cleaned that up when I got her running). What's the best harness to get? Then to combine these, has anyone ripped out the floor pans, then re-wired using the nice large holes in the floor to get up into the dash from underneath? I have a 4 post lift, so I'm thinking if tough to get under the dash, that might make it easier. Is that a crazy idea? Would it even work?

01-12-2023, 11:08 PM	#2
62c30 Registered User Join Date: Jan 2017 Location: Derby Kansas Posts: 386	Re: Floorboards and wire harness??? I pieced in places on my 61 truck, if I could redo it I would have done a one piece floor. I have not used a one piece floor so I don't know on the brands. I'm sure it's like every other aftermarket sheet metal and will probably need some work. I usually buy from LMC and classic parts. LMC gives a discount if you order the day before and pick up in person.

01-13-2023, 07:28 AM	#3
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: Floorboards and wire harness??? I found it pretty easy to wire the cab/dash with the seat out. I also removed the gauge panel and wired everything so that I could plug it all in when I re-installed it. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

01-13-2023, 11:05 AM	#4
Winchrig Registered User Join Date: Apr 2022 Location: Michigan Posts: 20	Re: Floorboards and wire harness??? I just redid the wiring harness in my 65 gmc 5000 last summer. I got a universal GM wiring harness through painless wiring. It was super easy, all the wires were labeled and it came with a detailed instruction book. __________________ 1965 GMC 5000 with toro flo diesel 1964 GMC b7000 twin stick winch truck with Detroit 6-71 1966 Oshkosh plow truck 1941 Dodge WC-27 ambulance

01-13-2023, 12:07 PM	#5
Arne Registered User Join Date: Sep 2022 Location: Eugene, OR Posts: 490	Re: Floorboards and wire harness??? I replaced most all of the wiring on my '64 with harnesses from American Autowire. They have stock restoration harnesses, update harnesses with more circuits, and full custom kits. I used stock restoration kits, but with a couple of custom options for passenger-side alternator and HEI. Pretty much plug and play. I've linked their website, but their products can be bought from other suppliers as well, sometimes a couple of bucks cheaper. https://www.americanautowire.com/ __________________ . - Arne Finished Project - 1964 C10 Stepside, mild restomod ———————————— Last edited by Arne; 01-14-2023 at 12:24 AM.

01-13-2023, 12:38 PM	#6
jweb Senior Member Join Date: Apr 2010 Location: Oregon Posts: 1,208	Re: Floorboards and wire harness??? The floor of the suburban is different than the trucks. So depending on where your issues are you may be piecing it anyway. __________________ 1951 Truck, LS1/4L60 1964 Suburban, current project 2014 Silverado daily driver 1953 Westerner "canned ham" trailer, rebuilt 1974 Prowler trailer, rebuilt



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.