1967 3/4 4x4 Burb question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**John Fabris** · 01-16-2004, 03:16 PM

Hi All,

I am going to look at a 67 3/4 ton 4x4 burb. My question is did they make a 4x4 burb in 67? I have never seen one with the KE vin. I have seen 69 and 70 factory 4x4 burbs.

Just wondering....

Also, there are several posts about production numbers, and I was wondering if someone who has the production numbers could post them for 1967-1972 for trucks, blazers, panels, and suburban in the FAQ section??

toms68cst · 01-16-2004, 04:08 PM

A 67 4X4 3/4 ton Burb is going to be a pretty low production number. My book shows 299.

As a comparison.

11,004 1/2 ton 2wd

4259 1/2 ton 4wd

1047 3/4 ton 2wd

All numbers are for 67 Burbs. I don't know how many would be GMC's or if they are included in that number.

**CPNE** · 01-16-2004, 04:19 PM

And if 67 was like other years, a barn-door model 4x4 is an even smaller percentage of 4x4 burb production than liftgate/tailgate model. Let's hope its a barn door burb!

**John Fabris** · 01-16-2004, 04:51 PM

thanks guys!! Is that info from the Chevy Truck red book? What other books show this type of info?

**John Fabris** · 01-16-2004, 07:15 PM

Just brought the book "The standard catalog of American Light-Duty Trucks", and it shows that for the "Chevy" 1967 3/4 ton 4x4 Suburban, 120 were made. Does not show GMC numbers...

*67Fleetsidedream* · 01-16-2004, 07:23 PM

I would jump on it.

**John Fabris** · 01-17-2004, 12:04 AM

Well, it is a factory 67 3/4 ton 4x4 Subruban. Was yellow, now painted red (macco or Earl Schibe job). Body is OK, with very few dings, has bondo here and there. Has rust in all three rockers, and two front outriggers have rust. Every door has a little rust along bottom. It does have the barn doors. Both chrome bumpers are bent. It has the two front rows of seats. Has 350 chevy crate motor. Runs and drive well (although front driveshaft is out) and it has current registration. What should I offer him?? He said best offer and did not say what price has alreadby offered if any.

Big Pictures Here!!!

toms68cst · 01-17-2004, 12:52 AM

It's hard to tell exactly what's under that red paint as far as rust and bondo are concerned. It looks like the drivers side rear 1/4 area was painted recently. (That's the way it looks in the pictures?) I'd take a small magnet and carefully check all the lower parts of the truck for bondo'd areas.

What's he asking? Around here something like that would run $1000-$1500 tops.

What are your plans for it if you do buy it?

teeitup · 01-17-2004, 01:12 AM

Well I had a 68 1/2 4x4 burb with gate not doors probably about same condition body wise but it didn't have the paint and got $2100 out of it here. This one is rare compared to it. Good luck, Randy

1969 GMC · 01-17-2004, 01:34 AM

did you happen to nab a pic of the gb sticker?

that thing is damn sweet, even though it looks like someone hosed it down with mustard and ketchup. i wonder wht engine it originally had. but, it will have an SM420 tranny and the Rockwell transfer, unless someone swapped em out. I'd say start at $2500 and work up.

lukecp · 01-17-2004, 01:38 AM

I agree with Adam....even with rusty rockers and a little door rust....a rare 4x4 (and 3-door

) burb like that i would price at around $2500 if not more. Along as it isn't a bondo-beast with lots of hidden problems anyway.

If he is asking for a offer tell him $1500 and go from there.

**Canadian694x4** · 01-17-2004, 02:15 AM

I'd Start $1500 too...go from there...does the owner know it's a rare burb?

GMC71k20 · 01-17-2004, 02:49 AM

offer him 5 dollars for the truck in $1495 for that tow hook

1969 GMC · 01-17-2004, 04:33 AM

i didn't even notice that it only had one!

Longhorn Man · 01-17-2004, 09:08 AM

I'd be all over that like ugly on an Osborne.

onetoncrewcab · 01-17-2004, 09:46 AM

I have to agree with the rest. I'd say anything under $3000 would be a steal for that. Looking at all the additional pictures, it does not appear to be in that bad of shape. And if the production numbers are correct for a 67 3/4t Sub with barn doors, you probably should hope the seller does not have that info.

Plus the fact it is a rare three door!

(or would it be a rarer five door?)
MJ (DISCLAIMER: No relation to the other MJ)

CliffB · 01-17-2004, 02:27 PM

Hey John,

You sound like you are acting like I do! This won't get in front of time on the 67 will it?

I vowed I would sell something and not bring anything else home for a long while. Then the 71 K20 had to join the fleet last month!

I enjoyed trading emails the other day. Where did you hear about this one? Look forward to your next news on it.

Regards,

Cliff

**John Fabris** · 01-18-2004, 02:50 PM

Hi All, I talked to the guy last night, and he is asking $2500 firm. That is what it cost him to have a shop put in the new engine last year. So he is trying to recoop that cost. I offered him $1500, and I left him my number. I am going to wait a few days ad then call him again. I have been watching this burb for three months now, and he has not been able to sell it. The guy moved to Portland and burb is in front of his mom's house near Oakland CA, and he is not doing any advertising.

72MARIO · 01-18-2004, 02:57 PM

Just wait on it buddy.

Hey when are you going to finish your 67 ? Man is that project going to be a career ?

Later

**John Fabris** · 01-18-2004, 10:48 PM

Ouch!! Oh well Mario, you got me there. I have working hard all this month to get rid of most of my other projects. The 2wd blazer has been traded for bodywork and paint on my 67. All of the motorcycles are for sale, and I have about four more days worth of work to get the Thunderbird back on the road and that will be sold as well. I am trying!!!

01-16-2004, 03:16 PM	#1
John Fabris TOTY 2006 Join Date: Dec 1999 Location: Magalia CA USA Posts: 2,270	1967 3/4 4x4 Burb production question Hi All, I am going to look at a 67 3/4 ton 4x4 burb. My question is did they make a 4x4 burb in 67? I have never seen one with the KE vin. I have seen 69 and 70 factory 4x4 burbs. Just wondering.... Also, there are several posts about production numbers, and I was wondering if someone who has the production numbers could post them for 1967-1972 for trucks, blazers, panels, and suburban in the FAQ section?? __________________ John Fabris 67 C10 SWB Last edited by John Fabris; 01-16-2004 at 03:55 PM.

01-16-2004, 04:08 PM	#2
toms68cst Registered User Join Date: Jun 2000 Location: Bismarck, ND Posts: 4,300	A 67 4X4 3/4 ton Burb is going to be a pretty low production number. My book shows 299. As a comparison. 11,004 1/2 ton 2wd 4259 1/2 ton 4wd 1047 3/4 ton 2wd All numbers are for 67 Burbs. I don't know how many would be GMC's or if they are included in that number. __________________ Unrestored 68 C-10 CST. Original 327. 4-Speed CH465. 50k or so miles. TREASURER, Drum Brake Club.

01-16-2004, 04:19 PM	#3
CPNE Resident Curmudgeon Join Date: Dec 1999 Location: NH Posts: 6,662	And if 67 was like other years, a barn-door model 4x4 is an even smaller percentage of 4x4 burb production than liftgate/tailgate model. Let's hope its a barn door burb! __________________ Currently on or near the homestead: 67 Chevy SWB 2WD stepside 350/3 on tree (Pat's) 67 GMC SWB 2WD Fleet 402/auto (Brian's under construction) 67 Chevy 3/4 ton 2WD 402/auto (Business Hauler) 67 Chevy 1 ton dually 2WD 396/4 speed (Former business hauler, Needs TLC) 68 Chevy 1/2 ton Suburban 2WD 250 six/3 on tree (Brian's Needs TLC) 70 Chevy 3/4 ton 4WD 350/4 speed (Pat's - Disguised as a 68 GMC) 71 Chevy SWB stepside (Crushed by tree - parts donor) 72 Chevy 3/4 ton 4WD (Parts donor) 72 Chevy 3/4 ton 4WD Suburban (Parts Donor) 72 GMC 3/4 ton 4WD 292 six/4 speed (Mine - Disguised as a 67 GMC) 81 GMC 4WD Dually Dump Body 350/4 speed (Business Hauler) 82 Camaro Z/28 355/Super T-10 (Pat's toy) 93 Caprice 9C1 (Brian's Cop Car) 02 Toyota Camry (Reliable but a souless steel and plastic hulk) 2011 2SS RS Camaro M6 Factory Hurst Shifter Maybe I need to sell some of this crap Yet another Bozo with a sawz-all

01-16-2004, 04:51 PM	#4
John Fabris TOTY 2006 Join Date: Dec 1999 Location: Magalia CA USA Posts: 2,270	thanks guys!! Is that info from the Chevy Truck red book? What other books show this type of info? __________________ John Fabris 67 C10 SWB

01-16-2004, 07:15 PM	#5
John Fabris TOTY 2006 Join Date: Dec 1999 Location: Magalia CA USA Posts: 2,270	Just brought the book "The standard catalog of American Light-Duty Trucks", and it shows that for the "Chevy" 1967 3/4 ton 4x4 Suburban, 120 were made. Does not show GMC numbers... __________________ John Fabris 67 C10 SWB

01-16-2004, 07:23 PM	#6
67Fleetsidedream Wiseass secured himself a BAN Join Date: Nov 2000 Location: MOON!!! Posts: 2,282	I would jump on it.

01-17-2004, 12:04 AM	#7
John Fabris TOTY 2006 Join Date: Dec 1999 Location: Magalia CA USA Posts: 2,270	Took a look at it Friday night... Well, it is a factory 67 3/4 ton 4x4 Subruban. Was yellow, now painted red (macco or Earl Schibe job). Body is OK, with very few dings, has bondo here and there. Has rust in all three rockers, and two front outriggers have rust. Every door has a little rust along bottom. It does have the barn doors. Both chrome bumpers are bent. It has the two front rows of seats. Has 350 chevy crate motor. Runs and drive well (although front driveshaft is out) and it has current registration. What should I offer him?? He said best offer and did not say what price has alreadby offered if any. Big Pictures Here!!! __________________ John Fabris 67 C10 SWB

01-17-2004, 12:52 AM	#8
toms68cst Registered User Join Date: Jun 2000 Location: Bismarck, ND Posts: 4,300	It's hard to tell exactly what's under that red paint as far as rust and bondo are concerned. It looks like the drivers side rear 1/4 area was painted recently. (That's the way it looks in the pictures?) I'd take a small magnet and carefully check all the lower parts of the truck for bondo'd areas. What's he asking? Around here something like that would run $1000-$1500 tops. What are your plans for it if you do buy it? __________________ Unrestored 68 C-10 CST. Original 327. 4-Speed CH465. 50k or so miles. TREASURER, Drum Brake Club.

01-17-2004, 01:12 AM	#9
teeitup Just like to part out trucks!! Join Date: Nov 2001 Location: Meriden, Ks-North of Topeka 10 miles Posts: 27,395	Well I had a 68 1/2 4x4 burb with gate not doors probably about same condition body wise but it didn't have the paint and got $2100 out of it here. This one is rare compared to it. Good luck, Randy __________________ 67 Chev swb stepside 4x4 283 4 speed SOLD 72 blazer 4x4 4 speed Cheyenne 72 GMC swb 4x4 fleet 4 speed, original paint 1958 Cameo (one of 1405 built, it was my dads) 2020 chevy Apex 4x4 crew cab 1969 Z28 with the 302 1980 chevy swb 4x4 1964 chevell Malibu SS 1976 K20, sold new originally out of my dads chevy dealership Members that I've met, over 200 probably closer to 300 in the 12 years I've been on this site, everyone I met "It was a pleasure" Last edited by teeitup; 01-17-2004 at 01:41 AM.

01-17-2004, 01:34 AM	#10
1969 GMC Registered User Join Date: Feb 2003 Location: The Rubber City Posts: 5,498	did you happen to nab a pic of the gb sticker? that thing is damn sweet, even though it looks like someone hosed it down with mustard and ketchup. i wonder wht engine it originally had. but, it will have an SM420 tranny and the Rockwell transfer, unless someone swapped em out. I'd say start at $2500 and work up. __________________ 1969 GMC K2500 1996 Honda Accord 2007 Kawasaki KLR 650

01-17-2004, 01:38 AM	#11
lukecp Formerly yellow72custom Join Date: May 2001 Location: Austin, TX Posts: 7,531	I agree with Adam....even with rusty rockers and a little door rust....a rare 4x4 (and 3-door ) burb like that i would price at around $2500 if not more. Along as it isn't a bondo-beast with lots of hidden problems anyway. If he is asking for a offer tell him $1500 and go from there. __________________ '72 Chevy C10 Mild 350/TH350/3.07. Ochre/White. Old high school ride. '70 GMC C2500 '62 327 4bbl/SM465/4.56-geared Dana 60. White/White. Project or parts truck. '97 Saturn SL DD. 1.9/5-speed. 40+ highway mpg

01-17-2004, 02:15 AM	#12
Canadian694x4 Born To Lose Club Join Date: Feb 2003 Location: Calgary, Alberta/Oxenden, Ontario, Great White North Posts: 13,307	I'd Start $1500 too...go from there...does the owner know it's a rare burb? __________________ Brian Smith - "Born To Lose" 1969 Chevrolet K10 LWB Fleetside - Proud Owner For 22 Yrs - 1 of 208 Built & Sold In Canada!- 283 V8/350TH/NP208, 2" All Spring Lift, 32" Good Year MT/R's. 1972 GMC K2500 Custom LWB Fleetside - Proud Owner For 3 Yrs - 1 of 571 Built & Sold In Canada! - 350 V8/SM465/NP205, 4” Rough Country Lift, 33” Interco TSL Thornbirds 2007.5 GMC Sierra SLE 2500HD 4x4 - Proud Owner For 17 Yrs- 6.6L V8 Duramax Diesel/Allison 1000, 2" Lift, 33" Mickey Thompson MTZ's. 2008 Yamaha Raptor 700r - Proud Owner For 15 Yrs - ITP Mud Lites. 2015 John Deere 1025R - Proud Owner For 8 Yrs - 24HP Diesel/H120/54D/260B/SB1154.

01-17-2004, 02:49 AM	#13
GMC71k20 Registered User Join Date: Aug 2002 Location: mass Posts: 1,277	offer him 5 dollars for the truck in $1495 for that tow hook

01-17-2004, 04:33 AM	#14
1969 GMC Registered User Join Date: Feb 2003 Location: The Rubber City Posts: 5,498	i didn't even notice that it only had one! __________________ 1969 GMC K2500 1996 Honda Accord 2007 Kawasaki KLR 650

01-17-2004, 09:08 AM	#15
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	I'd be all over that like ugly on an Osborne.



Register or Log In To remove these advertisements.

01-17-2004, 09:46 AM	#16
onetoncrewcab One of my kids. Cute eh? Join Date: Oct 2001 Location: Mitchell, SD Posts: 1,286	I have to agree with the rest. I'd say anything under $3000 would be a steal for that. Looking at all the additional pictures, it does not appear to be in that bad of shape. And if the production numbers are correct for a 67 3/4t Sub with barn doors, you probably should hope the seller does not have that info. Plus the fact it is a rare three door! (or would it be a rarer five door?) MJ (DISCLAIMER: No relation to the other MJ) __________________ If a kid asks where rain comes from, I think a cute thing to tell him is “God is crying.” And if he asks why God is crying, another cute thing to tell him is “Probably because of something you did. John 3:16 2006 Chevy HHR 2000 Dodge Durango 1985 Jeep CJ-7 1970 Chevy Pickup

01-17-2004, 02:27 PM	#17
CliffB Registered User Join Date: Dec 2003 Location: San Leandro, CA Posts: 83	Hey John, You sound like you are acting like I do! This won't get in front of time on the 67 will it? I vowed I would sell something and not bring anything else home for a long while. Then the 71 K20 had to join the fleet last month! I enjoyed trading emails the other day. Where did you hear about this one? Look forward to your next news on it. Regards, Cliff __________________ 72 C20 3/4 Custom Camper 94 Roadmaster Estate Wagon

01-18-2004, 02:50 PM	#18
John Fabris TOTY 2006 Join Date: Dec 1999 Location: Magalia CA USA Posts: 2,270	Hi All, I talked to the guy last night, and he is asking $2500 firm. That is what it cost him to have a shop put in the new engine last year. So he is trying to recoop that cost. I offered him $1500, and I left him my number. I am going to wait a few days ad then call him again. I have been watching this burb for three months now, and he has not been able to sell it. The guy moved to Portland and burb is in front of his mom's house near Oakland CA, and he is not doing any advertising. __________________ John Fabris 67 C10 SWB

01-18-2004, 02:57 PM	#19
72MARIO Registered User Join Date: Nov 2000 Location: Huntsville Ontario Canada Posts: 4,051	Just wait on it buddy. Hey when are you going to finish your 67 ? Man is that project going to be a career ? Later __________________ 1968 Suburban numbers matching all original truck now equipped with 6.0/4L80 on Accuair http://67-72chevytrucks.com/vboard/s...d.php?t=625017 1967 C/20 6.0/4L80 Roofing Truck 1990 V2500 Suburban "Plow Truck" 2005 TAHOE DD

01-18-2004, 10:48 PM	#20
John Fabris TOTY 2006 Join Date: Dec 1999 Location: Magalia CA USA Posts: 2,270	Ouch!! Oh well Mario, you got me there. I have working hard all this month to get rid of most of my other projects. The 2wd blazer has been traded for bodywork and paint on my 67. All of the motorcycles are for sale, and I have about four more days worth of work to get the Thunderbird back on the road and that will be sold as well. I am trying!!! __________________ John Fabris 67 C10 SWB

Register or Log In To remove these advertisements.