Steering shaft - The 1947 - Present Chevrolet & GMC Truck Message Board Network

2wdBlazer · 02-18-2004, 03:18 PM

Anyone know the spline sizes into the box or into the column or length? I would like to get a custom shaft made since I can't find an aftermarket one.

2wdBlazer · 02-18-2004, 03:27 PM

Oh, This is for a 4x4 as well.

bouncytruck · 02-18-2004, 04:38 PM

Do you have cross over? If not, you should consider it before getting the sterring shaft made, especiall with the big meats you got on that thing.

2wdBlazer · 02-18-2004, 06:39 PM

No Crossover and don't intend to. It drives very, very straight already and really doen't have bump steer at all. My stock shaft is on it's last leg though. I have contacted Borgeson Corp and they need those measurements to make a custom shaft. They are very good strength and quality.

Anyone know of a company that sells shafts that will fit? I don't wanna take my daily driver apart to make measurements.

blazer1971 · 02-18-2004, 09:40 PM

Take it to Bob's machine shop over the bridge in Ruskin.

2wdBlazer · 02-20-2004, 10:55 AM

Anyone got A parts truck laying around for measurements?

69k5 · 02-20-2004, 04:16 PM

i have a 72 4x4 k 20 . what exact measure ments do you need?

69k5

2wdBlazer · 02-20-2004, 05:50 PM

Length from box to column where it bolts up. Spline count on each side where it bolts in.

69k5 · 02-20-2004, 09:03 PM

ill see what i can do tonight and let you know tommorrow.

BLAZERMAN · 02-21-2004, 02:53 PM

You might give Flaming River a try.
http://www.flaming-river.com/enter.htm

69k5 · 02-21-2004, 07:37 PM

Quote:

Originally posted by 69k5
i have a 72 4x4 k 20 . what exact measure ments do you need?

69k5

19 7/8 from the ltip of the clamp where it joins the column. that is with about an 1/8 between the clamp and the round black part of the column. and is measured from the lower part in the rag joint?(4 bolts that hold the shaft to the box. ) 36 splines on the column end. i couldnt get the other end off to count but i imagine its the same.

69k5

earl87gta · 02-22-2004, 02:11 PM

Thier is a guy over at CK5.com that sells them for $75 I think If you go to the salvage yard you can get one out of a van and cut the center section down the vans use 2 ujoints like the flaing river joints and a vibraion dampner My joint with the dampner for my truck came from a van and Im using a flaiming river at the coulume and I only have abought $85 in the hole thing would have had alot less if I would have known abought the van thing.

1971 2wd · 02-24-2004, 04:48 PM

Cut out the middle section [-------------]
Drill out thr area where the shaft is 3/4" and put in a chunck of 3/4" chrome rod [=======] BLING BLING

Very trick and you lose the Collapsable junk. Done it on my 2wd, very easy to do..

earnhardt221 · 03-23-2004, 06:57 PM

i have the stock shaft from a 4x4 if u need one (cheap)
E-mail: earnhardt221@aol.com

02-18-2004, 03:18 PM	#1
2wdBlazer The Blazer King Join Date: Sep 2000 Location: Valrico, Fl (Tampa) Posts: 1,212	Steering shaft Anyone know the spline sizes into the box or into the column or length? I would like to get a custom shaft made since I can't find an aftermarket one. __________________ 72 2wd Blazer. Its the superbichinest, megacoolinest, superflowinest.

02-18-2004, 03:27 PM	#2
2wdBlazer The Blazer King Join Date: Sep 2000 Location: Valrico, Fl (Tampa) Posts: 1,212	Oh, This is for a 4x4 as well. __________________ 72 2wd Blazer. Its the superbichinest, megacoolinest, superflowinest.

02-18-2004, 04:38 PM	#3
bouncytruck SKINNY TIRES RULE! Join Date: Sep 2001 Location: Bothell, WA Posts: 11,038	Do you have cross over? If not, you should consider it before getting the sterring shaft made, especiall with the big meats you got on that thing. __________________ bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L

02-18-2004, 06:39 PM	#4
2wdBlazer The Blazer King Join Date: Sep 2000 Location: Valrico, Fl (Tampa) Posts: 1,212	No Crossover and don't intend to. It drives very, very straight already and really doen't have bump steer at all. My stock shaft is on it's last leg though. I have contacted Borgeson Corp and they need those measurements to make a custom shaft. They are very good strength and quality. Anyone know of a company that sells shafts that will fit? I don't wanna take my daily driver apart to make measurements. __________________ 72 2wd Blazer. Its the superbichinest, megacoolinest, superflowinest.

02-20-2004, 10:55 AM	#6
2wdBlazer The Blazer King Join Date: Sep 2000 Location: Valrico, Fl (Tampa) Posts: 1,212	Anyone got A parts truck laying around for measurements? __________________ 72 2wd Blazer. Its the superbichinest, megacoolinest, superflowinest.

02-18-2004, 09:40 PM	#5
blazer1971 Registered User Join Date: Apr 2001 Location: apollo bch,fl. usa Posts: 134	Take it to Bob's machine shop over the bridge in Ruskin.

02-20-2004, 04:16 PM	#7
69k5 Registered User Join Date: Nov 2003 Location: Monroe, La 71202 Posts: 317	i have a 72 4x4 k 20 . what exact measure ments do you need? 69k5

02-20-2004, 05:50 PM	#8
2wdBlazer The Blazer King Join Date: Sep 2000 Location: Valrico, Fl (Tampa) Posts: 1,212	Length from box to column where it bolts up. Spline count on each side where it bolts in. __________________ 72 2wd Blazer. Its the superbichinest, megacoolinest, superflowinest.

02-20-2004, 09:03 PM	#9
69k5 Registered User Join Date: Nov 2003 Location: Monroe, La 71202 Posts: 317	ill see what i can do tonight and let you know tommorrow.

02-21-2004, 02:53 PM	#10
BLAZERMAN Currently Blazerless Join Date: Apr 2000 Location: St. Joseph Mo. Posts: 4,828	You might give Flaming River a try. http://www.flaming-river.com/enter.htm __________________ 1972 C/30 133" W.B. C&C 1970 GMC 3500 157" W.B. single wheel C&C

02-22-2004, 02:11 PM	#12
earl87gta Senior Member Join Date: Dec 2003 Location: Kingsport TN Posts: 4,641	Thier is a guy over at CK5.com that sells them for $75 I think If you go to the salvage yard you can get one out of a van and cut the center section down the vans use 2 ujoints like the flaing river joints and a vibraion dampner My joint with the dampner for my truck came from a van and Im using a flaiming river at the coulume and I only have abought $85 in the hole thing would have had alot less if I would have known abought the van thing. __________________ Earl 68 2500 4x4 GMC Burb

02-24-2004, 04:48 PM	#13
1971 2wd Registered User Join Date: Jan 2003 Location: PARADISE,CA Posts: 57	Cut out the middle section [-------------] Drill out thr area where the shaft is 3/4" and put in a chunck of 3/4" chrome rod [=======] BLING BLING Very trick and you lose the Collapsable junk. Done it on my 2wd, very easy to do.. __________________ 72 blazer, 71 2wd short bed, 67 nova Too many damn toys!!

03-23-2004, 06:57 PM	#14
earnhardt221 Registered User Join Date: Jun 2001 Location: Bear De. USA Posts: 52	i have the stock shaft from a 4x4 if u need one (cheap) E-mail: earnhardt221@aol.com



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.