complete 6 cylinder - The 1947 - Present Chevrolet & GMC Truck Message Board Network

brian mac · 02-20-2009, 08:18 PM

This is a running 6 cylinder from my 1968 GMC. It has a HEI distributor. It does leak oil from the front crankshaft seal. It smoked a small amount when first started. Local pickup only. $200 Sorry I do not know how to post pics.

brian mac · 02-21-2009, 07:39 PM

bump

brian mac · 02-22-2009, 08:48 AM

make an offer I need it out of the way. maybe i need to part out the engine?

brian mac · 02-22-2009, 07:46 PM

bump

brian mac · 02-23-2009, 07:31 PM

bump

Erl · 02-24-2009, 02:15 PM

Is it a V6? If so, PM me.

ERL

brian mac · 02-24-2009, 03:15 PM

This is an inline 6.

vasquezmrysvll · 02-24-2009, 09:07 PM

i need the oil pressure fitting on the right side of the block, below the rear side cover.

OhNoJoe · 02-24-2009, 11:48 PM

can you email me some pic of the carb set-up

brian mac · 02-25-2009, 09:37 AM

The oil pressure fitting is just a sensor for the dash light (one wire connector) is that what you need?

I do not know how to email or post pics. I have a digital camera but I am computer "challenged" . The carb is a holley reman monojet.

vasquezmrysvll · 02-25-2009, 10:31 AM

i need the fitting for the gauge. thanks for your time

tommyd241 · 02-25-2009, 11:56 AM

Quote:

Originally Posted by brian mac

This is a running 6 cylinder from my 1968 GMC. It has a HEI distributor. It does leak oil from the front crankshaft seal. It smoked a small amount when first started. Local pickup only. $200 Sorry I do not know how to post pics.

How much for the HEI distributor, spark plug wires, and HEI power wire shipped to 87107? Basically the entire HEI system.

brian mac · 02-25-2009, 01:06 PM

how about 75.00 shipped on the hei setup. Let me check and make sure it has the proper connector for the power wire

68C10HotRod · 02-25-2009, 01:19 PM

Which inline 6 is it? 230, 250 or 292? 292 is the only one with the motor mount between the fuel pump & distributor. All the others have the fuel pump & mount reversed. Might help it sell if ppl know what it is.

tommyd241 · 02-25-2009, 01:56 PM

Quote:

Originally Posted by brian mac

how about 75.00 shipped on the hei setup. Let me check and make sure it has the proper connector for the power wire

Yeah LMK and yeah which inline 6 is it? I don't think it matters for me with the HEI set-up, but I'm sure people would like to know. Mine is a 250.

brian mac · 02-25-2009, 04:18 PM

tommyd

It does not have the proper connector for the power wire. I am told these are available at most local parts stores.

brian mac · 02-25-2009, 04:22 PM

tommyd

It does not have the proper connector for the power wire. I am told these are available at most local parts stores. How do you tell if it is a 230, 250 etc. Where are the casting numbers

tommyd241 · 02-25-2009, 04:28 PM

Quote:

Originally Posted by brian mac

tommyd

It does not have the proper connector for the power wire. I am told these are available at most local parts stores. How do you tell if it is a 230, 250 etc. Where are the casting numbers

I don't exactly know, but I'm sure one of the old-timers will chime in. Take a picture of it. Here is what my 250 looks like.

brian mac · 02-26-2009, 09:47 AM

bump

brian mac · 02-27-2009, 09:40 AM

OK, since nobody is interested it is going to the scrap yard!!! SOON!!!

RJGeister · 02-27-2009, 04:08 PM

BM,
Got a casting numbers off of the block? That would tell folks what inline 6 it is. VIN number would help if the motor is original to he truck. Might help the sale.

Rich

brian mac · 03-01-2009, 09:35 AM

casting number
473483
distributor pad number
f1203tub

68C10HotRod · 03-01-2009, 04:19 PM

Block # indicates this is a 250cid from a passenger car 1966-1979. Got the info from "Chevrolet Inline Six-Cylinder Power Manual". Don't see any info to decode the dist pad # but it does indicate where the block was cast & it's dress (comp ratio & accessories).

brian mac · 03-02-2009, 11:22 AM

bump

brian mac · 03-03-2009, 09:00 PM

bump

02-20-2009, 08:18 PM	#1
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	complete 6 cylinder This is a running 6 cylinder from my 1968 GMC. It has a HEI distributor. It does leak oil from the front crankshaft seal. It smoked a small amount when first started. Local pickup only. $200 Sorry I do not know how to post pics.

02-21-2009, 07:39 PM	#2
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder bump

02-22-2009, 08:48 AM	#3
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder make an offer I need it out of the way. maybe i need to part out the engine? Last edited by brian mac; 02-22-2009 at 08:49 AM.

02-22-2009, 07:46 PM	#4
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder bump

02-23-2009, 07:31 PM	#5
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder bump

02-24-2009, 02:15 PM	#6
Erl Registered User Join Date: Mar 2002 Location: Dallas, TX Posts: 555	Re: complete 6 cylinder Is it a V6? If so, PM me. ERL __________________ 1968 GMC 305 V6 3/4 4x4 Stepside 06 Corvette Daily Driver Dallas TX

02-24-2009, 03:15 PM	#7
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder This is an inline 6.

02-24-2009, 09:07 PM	#8
vasquezmrysvll "the other guy" Join Date: Oct 2008 Location: Olivehurst California 95961 Posts: 901	Re: complete 6 cylinder i need the oil pressure fitting on the right side of the block, below the rear side cover. __________________ God Said,"Building A 10 Second Import Is Like Coming Out Of The Closet, In The End Ur Still....."EXPLETIVE"

02-24-2009, 11:48 PM	#9
OhNoJoe Registered User Join Date: May 2006 Location: Springfield Illinois Posts: 182	Re: complete 6 cylinder can you email me some pic of the carb set-up

02-25-2009, 09:37 AM	#10
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder The oil pressure fitting is just a sensor for the dash light (one wire connector) is that what you need? I do not know how to email or post pics. I have a digital camera but I am computer "challenged" . The carb is a holley reman monojet.

02-25-2009, 10:31 AM	#11
vasquezmrysvll "the other guy" Join Date: Oct 2008 Location: Olivehurst California 95961 Posts: 901	Re: complete 6 cylinder i need the fitting for the gauge. thanks for your time __________________ God Said,"Building A 10 Second Import Is Like Coming Out Of The Closet, In The End Ur Still....."EXPLETIVE"

02-25-2009, 01:06 PM	#13
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder how about 75.00 shipped on the hei setup. Let me check and make sure it has the proper connector for the power wire

02-25-2009, 01:19 PM	#14
68C10HotRod Registered User Join Date: Feb 2008 Location: Omaha, NE 68144 Posts: 333	Re: complete 6 cylinder Which inline 6 is it? 230, 250 or 292? 292 is the only one with the motor mount between the fuel pump & distributor. All the others have the fuel pump & mount reversed. Might help it sell if ppl know what it is. __________________ Bryan '52 Bel Air 2dr HT - in pieces '68 C10 - 6cyl/4spd REMOVED, LT1/T56 to be installed “Any society that would give up a little liberty to gain a little security will deserve neither and lose both.” - Benjamin Franklin "And those who know what's best for us, Must rise and save us from ourselves" - RUSH lyric (mockery)

02-25-2009, 04:18 PM	#16
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder tommyd It does not have the proper connector for the power wire. I am told these are available at most local parts stores.

02-25-2009, 04:22 PM	#17
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder tommyd It does not have the proper connector for the power wire. I am told these are available at most local parts stores. How do you tell if it is a 230, 250 etc. Where are the casting numbers



Register or Log In To remove these advertisements.

02-26-2009, 09:47 AM	#19
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder bump

02-27-2009, 09:40 AM	#20
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder OK, since nobody is interested it is going to the scrap yard!!! SOON!!!

02-27-2009, 04:08 PM	#21
RJGeister Retired Air Force 87-09 Join Date: Feb 2007 Location: Bonaire, Georgia 31005 Posts: 284	Re: complete 6 cylinder BM, Got a casting numbers off of the block? That would tell folks what inline 6 it is. VIN number would help if the motor is original to he truck. Might help the sale. Rich

03-01-2009, 09:35 AM	#22
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder casting number 473483 distributor pad number f1203tub

03-01-2009, 04:19 PM	#23
68C10HotRod Registered User Join Date: Feb 2008 Location: Omaha, NE 68144 Posts: 333	Re: complete 6 cylinder Block # indicates this is a 250cid from a passenger car 1966-1979. Got the info from "Chevrolet Inline Six-Cylinder Power Manual". Don't see any info to decode the dist pad # but it does indicate where the block was cast & it's dress (comp ratio & accessories). __________________ Bryan '52 Bel Air 2dr HT - in pieces '68 C10 - 6cyl/4spd REMOVED, LT1/T56 to be installed “Any society that would give up a little liberty to gain a little security will deserve neither and lose both.” - Benjamin Franklin "And those who know what's best for us, Must rise and save us from ourselves" - RUSH lyric (mockery)

03-02-2009, 11:22 AM	#24
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder bump

03-03-2009, 09:00 PM	#25
brian mac Registered User Join Date: Dec 2008 Location: eufaula,alabama Posts: 198	Re: complete 6 cylinder bump

Register or Log In To remove these advertisements.